Template:Reference Tool models: Difference between revisions

Revision as of 08:15, 21 January 2017

Model	Type	Board	Flash	SB	Syscon	CP	BDemu HDD	GameOS HDD	Bluray Drive	HDMI Ports	OtherOS	CELL BE	RSX	USB Ports	GbLan Ports	Flash Readers	Support: PSP PS2 PS1	SA- CD	WiFi 802.11 b/g	SKU Release date	SDK/FW support	downgradeable Min. praxis	Other
DECR-1000(A/J)	0x01	TMU-520	2x 256MB NAND	CXD2973AGB-4	CXR713F120A	TCP-520	400GB	400GB	?0x00?	2 (NO CEC)	PARTIAL	90nm	90nm	4 + 2 extra	4 (1 for dbg.)	YES	?YES? NO NO	NO	YES	2006	=>1.0.0 or =>2.3.0 (since 1/2009)	<0.85.009	contains prototype components, hardware is much closer to DEH-R1040 than CECHAxx.
DECR-1400A/J	0x09	DEB-001	1x 16MB NOR	?CXD2984GB?	CXR713120-201GB	(via SB)	-	160 GB	?0x0A?	1 (NO CEC)	PARTIAL	45nm	65nm	4	2 (1 for dbg.)	NO	?YES? NO NO	NO	YES	6/2009	=>2.6.0	=>?2.60?	same case as retail PS3

Differences between the 1000 and 1400:

DECR-1000:
- Gb-DEVLAN is connected to the Communication Processor
- With a pre (or equal to) 0.85.010 bootrom you do have two HDMI outputs.
- Not all DECR-1000 are equal! Despite Sony's documentation claiming otherwise, DECR-1000 units with RSX rom version b07 and above such as refurbished/serviced units (and perhaps some others that have not been encounter) are not capable of running any firmware lower than 1.60 (from sdk 160.008) this is because the rom version is unknown/unsupported in older lv1 which will fail to initialize the RSX hardware and will cause lv1 to output a "rsx rom abort!" message, this will in turn create an exception early in lv2 boot process as it tries to use the RSX and creates a hard brick several RSX related errors such as "lv2(2): # __rsxaudio_intr_create_thread 983 ffffffff" or "graphics error 512 : 00012625 c221bbb0" ; "lv2(2): page fault handler (DSI): invalid access address 0x795d00e8!".

@@ Line 14: / Line 14: @@
 *[[DECR-1000]]:
 ** Gb-DEVLAN is connected to the [[Communication Processor]]
-** With a pre [[0.85.009]] bootrom you do have two [[HDMI]] outputs.
+** With a pre (or equal to) [[0.85.010]] bootrom you do have two [[HDMI]] outputs.
 <!-- ** Could be turned into a {{SD}} System Debugger by changing the [[South Bridge]] firmware, adding a special CP Sister Board and using a specific {{SD}} firmware -->
 ** '''Not all DECR-1000 are equal! Despite Sony's documentation claiming otherwise, DECR-1000 units with RSX rom version b07 and above such as refurbished/serviced units (and perhaps some others that have not been encounter) are not capable of running any firmware lower than 1.60 (from sdk 160.008) this is because the rom version is unknown/unsupported in older lv1 which will fail to initialize the RSX hardware and will cause lv1 to output a "rsx rom abort!" message, this will in turn create an exception early in lv2 boot process as it tries to use the RSX and creates a hard brick several RSX related errors such as "lv2(2): # __rsxaudio_intr_create_thread 983 ffffffff" or "graphics error 512 : 00012625 c221bbb0" ; "lv2(2): page fault handler (DSI): invalid access address 0x795d00e8!"'''.