JAISPI

Someone should translate the spanish resources into english for wiki here, please.

JAISPI

JAISPI - Raspberry Pi SPI flasher for PS4

Source:

• http://jaicrab.org/?&a=Raspberry/Article/JAISPI
• http://jaicrab.org/?&a=Ps4/Tools/JAISPI

JAISPI - Utility to read and write to the main memory (MX25L25635FMI-10G) of PS4 with the Raspberry Pi through the SPI protocol.

Changelog

• v1.0
  • Support MX25L25635FMI-10G
  • Reading
  • Programming
  • Full Erase

Installation Instructions

Materials Required

• 1x Raspberry Pi (see talkpage for where to buy)
• 1x SD Memory (for Raspbian, a 4GB minimal is recommended)
• 1x PS4 Serial Flash MX25L25635FMI-10G desoldered from console

Downloads

• Raspbian (http://downloads.raspberrypi.org/raspbian_latest)
• Win32 Disk Imager (http://sourceforge.net/projects/win32diskimager/files/latest/download)
• Putty (http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe)

Pinout

MX25L1006E Pinout

25X10CLYA1 Pinout

MX25L25635FMI-10G Pinout

Raspberry Pi GPIO pinout

8-Pin	16-pin	Usage	Raspberry Pi JAISPI	Description
-	1	SIO3	NC	8pin: Not Available - not used / 16pin: Serial Data Input & Output (for 4xI/O read mode)
8	2	VCC	17	+3V DC Power Supply
7	3	HOLD#/RESET#	NC	8pin: Hold, to pause the device without deselecting the device / 16pin: Hardware Reset Pin Active low
-	4	NC	NC	No Connection
-	5	NC	NC	No Connection
-	6	NC	NC	No Connection
1	7	CS#	24	Chip Select
2	8	SO/SIO1	21	Serial Data Output (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode)
3	9	WP#/SIO2	25	Write Protection: connect to GND or Serial Data Input & Output (for 4x I/O read mode)
4	10	GND	25	Ground
-	11	NC	NC	No Connection
-	12	NC	NC	No Connection
-	13	NC	NC	No Connection
-	14	NC	NC	No Connection
5	15	SI/SIO0	19	Serial Data Input (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode)
6	16	SCLK	23	Clock Input

Use short wires, esp. if you are not adding the 0.1µF capacitor between ground and vcc as close as possible to the chip

Installation

Installing Raspbian

Run win32diskimage

• In "Image file" select the downloaded and decompressed Raspbian image.
• In "Device" select the drive where the SD memory is.
• Select "Write".

After finished writing, put the SD card in the Raspberry Pi and power it up by inserting the USB cable.

Remote Shell into Raspbian

Two minutes after booting up the Raspberry Pi, run Putty.

• In Host Name put: raspberrypi
• In case the previous step doesnt works properly, go to the router and find the IP assigned to your Raspberry Pi.
• Select SSH.
• Select Open.

Installing Application

It will request a Login. According Raspbian the user is "pi" and the password "raspberry" (Both without quotes).

Insert the following commands:

sudo-s
cd /bin
wget http://jaicrab.org/Ps4/Tools/JAISPI/jaispi
chmod +x jaispi
echo "# blacklist spi-bcm2708"> / etc / modprobe.d / blacklist.conf raspi-
echo "blacklist i2c-bcm2708" >> / etc / modprobe.d / blacklist.conf raspi-
reboot

Installation is complete. By Putty you can access the Raspberry Pi. To run the command jaispi you need to be root (sudo-s):

# sudo-s
# Jaispi-i / dev/spidev0.0

Options

 -i /dev/spidevX.X             Get ID from flash
 -r file.bin /dev/spidevX.X    Read entire flash to file
 -e /dev/spidevX.X             Erase entire flash
 -p file.bin /dev/spidevX.X    Only write blocks differences from file
 -v file.bin /dev/spidevX.X    Verify blocks with file

Get ID

-i: Displays information of the flash.

#jaispi -i /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635

Read

-r: Makes a full dump of the flash (Average time: 35sec)

#jaispi -r DUMP.bin /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635
Reading...
0x02000000
Done!

Erase

-e: Clears all flash (Average time: 1min, 30sec)

#jaispi -e /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635
Erasing blocks...
Done!

Program

-p: Write to flash only the changed sectors (Average time: 1min 30sec)

#jaispi -p Base.bin /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635
Starting...
0x02000000 -> 8192 Sectors written
Done!

Verify

-v: Compares the flash contents with a file in PC (Average time: 35sec)

#jaispi -v Base.bin /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635
Checking...
0x02000000 -> 0 Different sectors
Done!