Syscon Hardware

Syscon 1st Generation (BGA Packaging)

Syscon is the main power controller chip. It is responsible for powering up the various power systems and for configuring and initialising the CELL BE, RSX and South Bridge. It communicates with these devices via seperate SPI busses. There is external access by JTAG (disabled at factory by blowing a fuse), an EEPROM programming interface and Serial (UART). The Syscon is a SoC and consists of an ARM7TDMI (ARMv4) CPU, a 256KB EEPROM and 16KB RAM.

Serialnumbers @ SKU

Retail

Model	Type	Board	Syscon part no.	Syscon Soft ID	Notes
CECHAxx CECHBxx	0x01 0x02	COK-001	CXR713120-201GB	0B8E
CECHCxx CECHExx	0x03 0x04	COK-002 or COK-002W	CXR713120-201GB or CXR713120-202GB	0C16
CECHGxx	0x05	SEM-001	CXR713120-201GB or CXR713120-202GB or CXR713120-203GB	0D52
CECHHxx	0x06	DIA-001	CXR714120-301GB	0DBF
CECHJxx CECHKxx	0x07	DIA-002	CXR714120-301GB or CXR714120-302GB	0E69
CECHLxx CECHMxx CECHPxx CECHQxx	0x08	VER-001	SW-301 or SW-302	065D
CECH-20xx	0x09	DYN-001	SW2-301	0832
CECH-21xx	0x0A	SUR-001	SW2-301 or SW2-302	08A0
CECH-25xx	0x0B	JTP-001 or JSD-001	SW2-301 or SW2-302  or SW2-303	08C2
CECH-30xx	0x0C	KTE-001	SW2-301 or SW2-302 or SW2-303	0918
CECH-40xx	0x0D	MSX-001 or MPX-001	SW3-302	098F

Non retail

Model	Type	Board	Syscon part no.	Syscon Soft ID	Active JTAG	Notes
CEB-2040	-	MPU-501	CXR713F120GB-000		Yes	Retail prototype
DECR1000(A/J)	0x01	TMU-520	CXR713F120A	03FB	?	Reference tool
DEH-H1000A(S)(-E(S))	0x01	COK-001 (Prototype)	CXR713F120A	0B67	?	Preproduction
DEH-H1001-D	0x01	COOKIE-13	CXR713F120A	?0B67?	?	Preproduction
DEH-FH1500J-A		VERTIGO-02				Preproduction

---

Not mentioned:

0F29 - ?
0F38 - ?

Syscon Externalised Ports

Note: for more specific information per model, see the links to each subppage in the Serialnumbers @ SKU table.

Syscon UART packets

SCUART daemon (SCUARTD) packet structure

SCUARTD packets includes header of 0x3 bytes and optional payload (depending on the command). Packet IDs are not important, they are used only by clients and processed by SCUART daemon. SCUART daemon opens terminal file /dev/ttyS0 and use it to send commands and receive responses.

Offset	Size	Description
0x00	0x01	Magic?
0x01	0x01	Payload size
0x02	0x01	Command
0x03	Payload size	Payload data

Packets

Packet ID	Command/Action	Description	Notes
0x00	version
0x01	bringup
0x02	shutdown
0x03	firmud	Firmware update	It actually notifies syscon for starting a firmware update operation and calls SX program which implements ZMODEM protocol for transfer
0x04	bsn	Board Serial Number	Retrieves Board Serial Number
0x05	halt
0x06	cp ready
0x07	cp busy
0x08	cp reset
0x09	bestat
0x0A	powersw
0x0B	resetsw
0x0C	bootbeep stat
0x0D	bootbeep on
0x0E	Reset mullion
0x0F	xdrdiag info
0x10	xdrdiag start
0x11	xdrdiag result
0x12	xiodiag
0x13	fandiag
0x14	errlog
0x15	Read line
0x16	tmpforcp
0x1F	cp beepremote
0x20	cp beep2kn1n3
0x21	cp beep2kn2n3

Real syscon packets have an ASCII form instead of bytes above.

An implementation of *MODEM transfer protocols used by Sony: https://github.com/jnavila/lrzsz/tree/master/src

Syscon UART

BGA	Name	Description
P16	UART0_TxD	Serial Transmit
P15	UART0_RxD	Serial Receive

You can attach a 3.3v TTL cable (LV-TTL) to the UART on syscon (UART0_TxD, UART0_RxD). Baud rate is 57600. There is a simple plaintext protocol involved. This varies on different syscon models. Example:

<command>:<hash>

Where the hash is the sum of command bytes & 0xFF

you should terminate commands with \r\n, the syscon messages are only terminated with \n

Samples

Here are some of the commands/messages encountered:

Messages:

Power applied (standby mode)
OK 00000000:3A

Power on
# (PowerOn State):7F

Power off (Hard shutdown)
# (PowerOff State):DD

After Fan test:
# (PowerOff State) (Fatal):36

No text, invalid hash:
NG F0000002:4D

Commands:

VER:ED
OK 00000000 S1E 00 00 065D:A4

ERRLOG:CB
OK 00000000:3A

DATE:1E
NG F0000003:4E

C:F1:BUZ
E:4F:NG F0000004

C:D0:CID
E:50:NG F0000005

C:DA:EEP
E:50:NG F0000005

C:D5:FAN
E:50:NG F0000005

C:F4:KSV
E:50:NG F0000005

C:ED:REV
E:50:NG F0000005

C:F8:SPU
E:50:NG F0000005

more Syscon commands

bruteforcing commands: http://pastebin.com/CNei0xbC

Syscon (SPI) EEPROM

BGA	Name	Description
F16	CSB	Chip Select (needs to be low)
H16	DO	Serial Data Output
G16	DI	Serial Data Input
E16	SKB	Serial Data Clock
J15	WCB	Write Protect
J16	RBB	Ready/Busy
G11	VDDep	+ 3.3V
C15	VSSep	GND

Syscon JTAG

disabled in factory after production on retailmodels

BGA	Name	Description
L8	JRTCK	Return Test Clock
K8	JTCK	Test Clock
K9	JTDO	Test Data Out
L9	JTMS	Test Mode State / Test Mode Select
K7	JTDI	Test Data In
L7	JNTRST	Test Reset

Syscon Underlaying ports

Syscon Cell SPI Bus

BGA	Name	Description
M2	/BE_SPI_CS	Chip Select
N2	BE_SPI_DO	Serial Data Output
M1	BE_SPI_DI	Serial Data Input
N1	BE_SPI_CLK	Serial Data Clock
P2	/BE_RESET	CellBE Reset
P1	BE_POWGOOD	CellBE PowerGood
T2	/BE_INT	CellBE Interrupt

Syscon Southbridge SPI Bus

BGA	Name	Description
B9	/SB_SPI_CS	Chip Select
B8	SB_SPI_DO	Serial Data Output
A9	SB_SPI_DI	Serial Data Input
A8	SB_SPI_CLK	Serial Data Clock