Template:Syscon pinout LQFP 100 pins: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
(This is not handy anymore, because all the remaining unknown pins was displayed as ←I/O→) |
||
| Line 14: | Line 14: | ||
| 1 || 14 || {{cellcolors|#77f|#ff0}} SCL20 || HDMI_I2C_SCL || {{pino}} || Connected to [[HDMI]] controller [[MN8647091]] pin 27 || 0 || 3.3V | | 1 || 14 || {{cellcolors|#77f|#ff0}} SCL20 || HDMI_I2C_SCL || {{pino}} || Connected to [[HDMI]] controller [[MN8647091]] pin 27 || 0 || 3.3V | ||
|- | |- | ||
| 2 || 14 || P141/PCLBUZ1/INTP7 || || | | 2 || 14 || P141/PCLBUZ1/INTP7 || || ? || Connected to [[South Bridge]] [[CXD9963GB]] pad AA17 (SB_RESET ?, or SB_CGRST ?) || || | ||
|- | |- | ||
| 3 || 14 || INTP6 || SB_INT || | | 3 || 14 || INTP6 || SB_INT || ? || Connected to [[South Bridge]] [[CXD9963GB]] pad W22 || || 3.3V | ||
|- | |- | ||
| 4 || 12 || {{cellcolors|#f93}} EXLVI || || {{pini}} || Connected to [[Power Supply]] main +12V rail through a <abbr title="The resistor/s and divider are located very close (but not connected) to the 4-pins BD ribbon cable connector">resistor and divider</abbr>. Related with [[Syscon_Error_Codes|Error Code 3001 ?]] || || 1.5V | | 4 || 12 || {{cellcolors|#f93}} EXLVI || || {{pini}} || Connected to [[Power Supply]] main +12V rail through a <abbr title="The resistor/s and divider are located very close (but not connected) to the 4-pins BD ribbon cable connector">resistor and divider</abbr>. Related with [[Syscon_Error_Codes|Error Code 3001 ?]] || || 1.5V | ||
|- | |- | ||
| 5 || 4 || P47/INTP2 || || | | 5 || 4 || P47/INTP2 || || ? || Connected to [[HDMI]] controller [[MN8647091]] pin 94 || || | ||
|- | |- | ||
| 6 || 4 || {{cellcolors|#246|#fff}} TO05 || BUZZER || {{pino}} || Connected to Buzzer- through a NPN 50V@100mA transistor || || 3.3V | | 6 || 4 || {{cellcolors|#246|#fff}} TO05 || BUZZER || {{pino}} || Connected to Buzzer- through a NPN 50V@100mA transistor || || 3.3V | ||
|- | |- | ||
| 7 || 4 || P45/SO01 || || | | 7 || 4 || P45/SO01 || || ? || Connected to bdrom IC pin 11 ([[Bluray Drive]] controller [[CXD5132R-1]] ? <abbr title="R8J32840FP1 in CECH-42xx, or R9J04G011FP1 in CECH-43xx">or...</abbr>) || || 3.3V | ||
|- | |- | ||
| 8 || 4 || {{cellcolors|#77f|#ff0}} P44/SI01 || THR_I2C_SDA || {{pinio}} || Connected to [[Thermal#Temperature_Monitors|TMP411A]] pin 7 through a 47ohm resistor (CELL Temperature Monitor, data)<br>Connected to [[Thermal#Temperature_Monitors|TMP411B]] pin 7 through a 47ohm resistor (RSX Temperature Monitor, data)<br>Connected to [[ISL6331]] pin 22 (Unknown Temperature sensor, data). And a testpad || 3.3V || 3.3V | | 8 || 4 || {{cellcolors|#77f|#ff0}} P44/SI01 || THR_I2C_SDA || {{pinio}} || Connected to [[Thermal#Temperature_Monitors|TMP411A]] pin 7 through a 47ohm resistor (CELL Temperature Monitor, data)<br>Connected to [[Thermal#Temperature_Monitors|TMP411B]] pin 7 through a 47ohm resistor (RSX Temperature Monitor, data)<br>Connected to [[ISL6331]] pin 22 (Unknown Temperature sensor, data). And a testpad || 3.3V || 3.3V | ||
| Line 30: | Line 30: | ||
| 9 || 4 || {{cellcolors|#77f|#ff0}} P43/<span style="text-decoration: overline;">SCK01</span> || THR_I2C_SCL || {{pino}} || Connected to [[Thermal#Temperature_Monitors|TMP411A]] pin 8 (CELL Temperature Monitor, clock)<br>Connected to [[Thermal#Temperature_Monitors|TMP411B]] pin 8 (RSX Temperature Monitor, clock)<br>Connected to [[ISL6331]] pin 23 (Unknown Temperature sensor, clock). And a testpad || 3.3V || 3.3V | | 9 || 4 || {{cellcolors|#77f|#ff0}} P43/<span style="text-decoration: overline;">SCK01</span> || THR_I2C_SCL || {{pino}} || Connected to [[Thermal#Temperature_Monitors|TMP411A]] pin 8 (CELL Temperature Monitor, clock)<br>Connected to [[Thermal#Temperature_Monitors|TMP411B]] pin 8 (RSX Temperature Monitor, clock)<br>Connected to [[ISL6331]] pin 23 (Unknown Temperature sensor, clock). And a testpad || 3.3V || 3.3V | ||
|- | |- | ||
| 10 || 4 || P42/TI04/TO04 || || | | 10 || 4 || P42/TI04/TO04 || || ? || Connected to [[South Bridge]] [[CXD9963GB]] pad AA18 (SB_RESET ?, or SB_CGRST ?) | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| Line 59: | Line 59: | ||
| 23 || data-sort-value="19"| || {{cellcolors|#f33|#fff}} EV<span style="font-size:60%;">DD0</span> || 3.3_EVER_B || {{pin}} || Connected to [[Talk:Regulators|Mitsumi 463A]] pin 2 (standby voltage regulator, secondary output power rail) || 3.3V || 3.3V | | 23 || data-sort-value="19"| || {{cellcolors|#f33|#fff}} EV<span style="font-size:60%;">DD0</span> || 3.3_EVER_B || {{pin}} || Connected to [[Talk:Regulators|Mitsumi 463A]] pin 2 (standby voltage regulator, secondary output power rail) || 3.3V || 3.3V | ||
|- | |- | ||
| 24 || 6 || P60/SCL0 || || | | 24 || 6 || P60/SCL0 || || ? || || || | ||
|- | |- | ||
| 25 || 6 || P61/SDA0 || || | | 25 || 6 || P61/SDA0 || || ? || || || | ||
|- | |- | ||
! style="padding:0px" data-sort-value="25.5"| || style="padding:0px" data-sort-value="0.5"| || style="padding:0px" colspan="6" | | ! style="padding:0px" data-sort-value="25.5"| || style="padding:0px" data-sort-value="0.5"| || style="padding:0px" colspan="6" | | ||
| Line 73: | Line 73: | ||
! style="padding:0px" data-sort-value="25.5"| || style="padding:0px" data-sort-value="4.5"| || style="padding:0px" colspan="6" | | ! style="padding:0px" data-sort-value="25.5"| || style="padding:0px" data-sort-value="4.5"| || style="padding:0px" colspan="6" | | ||
|- | |- | ||
| 26 || 6 || P62 || || | | 26 || 6 || P62 || || ? || Connected to <abbr title="64 pins">ISL IC</abbr> pin 3 || || 2.5V | ||
|- | |- | ||
| 27 || 6 || P63 || || | | 27 || 6 || P63 || || ? || Connected to [[switch boards|Switch board]] dual led (Red) through a dual digital NPN transistor EMH1(SOT-563) ? (STBY_LED ?) || 3.3V || | ||
|- | |- | ||
| 28 || 3 || P31/TI03/TO03/INTP4 || ACIN_DET ? || | | 28 || 3 || P31/TI03/TO03/INTP4 || ACIN_DET ? || ? || pin 4 to wifi5v vreg ic/EN ? | ||
|| || | || || | ||
|- | |- | ||
| 29 || 6 || P64 || || | | 29 || 6 || P64 || || ? || Connected (indirectly) to a voltage regulator ? (to enable something ?) || || 3.3V | ||
|- | |- | ||
| 30 || 6 || P65 || || | | 30 || 6 || P65 || || ? || Connected to IDT4227 pin 1 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 31 || 6 || {{cellcolors|#77f|#ff0}} P66 || MK_I2C_SCL ? || | | 31 || 6 || {{cellcolors|#77f|#ff0}} P66 || MK_I2C_SCL ? || ? || Connected to Texas Instruments-SCEI Clock Generator [[CDC750]] pin 33 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 32 || 6 || {{cellcolors|#77f|#ff0}} P67 || MK_I2C_SDA ? || | | 32 || 6 || {{cellcolors|#77f|#ff0}} P67 || MK_I2C_SDA ? || ? || Connected to Texas Instruments-SCEI Clock Generator [[CDC750]] pin 34 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 33 || 7 || P77/KR7/INTP11 || || | | 33 || 7 || P77/KR7/INTP11 || || ? || Connected to voltage regulator [[Talk:Regulators|Rohm BD3527]] pin 12 (enable USB ?) | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 34 || 7 || P76/KR6/INTP10 || || | | 34 || 7 || P76/KR6/INTP10 || || ? || Connected to [[ISL6331]] <abbr title="40 pins">pin 24</abbr> | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 35 || 7 || P75/KR5/INTP9 || || | | 35 || 7 || P75/KR5/INTP9 || || ? || Connected to [[South Bridge]] [[CXD9963GB]] pad U19 throught 4k7 resistor | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 36 || 7 || P74/KR4/INTP8 || || | | 36 || 7 || P74/KR4/INTP8 || || ? || Connected to [[ISL6331]] pin 20 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 37 || 7 || P73/KR3 || || | | 37 || 7 || P73/KR3 || || ? || Connected to [[Service_Connectors#CN.3F.3F.3F.3F|Service Connector 3rd Gen.]] pin 3<br>Connected to D35236SK pin 6 <!-- one of them have a typo ? D35236SK or D35326SK ? --> | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 38 || 7 || P72/KR2 || || | | 38 || 7 || P72/KR2 || || ? || Connected to D35326SK pin 7 <!-- one of them have a typo ? D35236SK or D35326SK ? --> | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| Line 112: | Line 112: | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 40 || 7 || P70/KR0 || || | | 40 || 7 || P70/KR0 || || ? || Connected to Texas Instruments [[PS53123]] pin 10 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 41 || 0 || P06 || || | | 41 || 0 || P06 || || ? || Connected to Texas Instruments [[PS53123]] pin 7 | ||
|| || | || || | ||
|- | |- | ||
| 42 || 0 || P05 || || | | 42 || 0 || P05 || || ? || Connected to Texas Instruments [[PS53123]] pin 17 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| Line 124: | Line 124: | ||
|| || | || || | ||
|- | |- | ||
| 44 || 8 || P80 || || | | 44 || 8 || P80 || || ? || 100K pull up to 3v3 | ||
|| || | || || | ||
|- | |- | ||
| Line 130: | Line 130: | ||
|| | || | ||
|- | |- | ||
| 46 || 8 || P82 || || | | 46 || 8 || P82 || || ? || Connected to [[HDMI]] controller [[MN8647091]] pin 95 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| Line 136: | Line 136: | ||
|| | || | ||
|- | |- | ||
| 48 || 8 || P84 || || | | 48 || 8 || P84 || || ? || Connected to pin1 EN vreg 8D11 (bottom side of power pcb) | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 49 || 8 || P85 || || | | 49 || 8 || P85 || || ? || Connected to Texas Instruments [[PS53123]] pin 3 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 50 || 8 || P86 || || | | 50 || 8 || P86 || || ? || Connected to IDT4227 pin 12 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| Line 155: | Line 155: | ||
! style="padding:0px" data-sort-value="50.5"| || style="padding:0px" data-sort-value="11.5"| || style="padding:0px" colspan="6" | | ! style="padding:0px" data-sort-value="50.5"| || style="padding:0px" data-sort-value="11.5"| || style="padding:0px" colspan="6" | | ||
|- | |- | ||
| 51 || 8 || P87 || || | | 51 || 8 || P87 || || ? || Connected to power pcb connector | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 52 || 3 || P30/INTP3/RTC1HZ || || | | 52 || 3 || P30/INTP3/RTC1HZ || || ? || Connected to [[ISL6331]] pin 21 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| Line 164: | Line 164: | ||
|| 3.3V || 3.3V | || 3.3V || 3.3V | ||
|- | |- | ||
| 54 || 5 || P50 || || | | 54 || 5 || P50 || || ? || Connected to [[ISL6331]] pin 25 | ||
|| || 3.3V | || || 3.3V | ||
|- | |- | ||
| 55 || 5 || P51 || || | | 55 || 5 || P51 || || ? || Connected to [[South Bridge]] [[CXD9963GB]] pad W21. And in line 10k to gnd || || | ||
|- | |- | ||
| 56 || 5 || {{cellcolors|#d9f|#fff}} P52 || WIFI_CTRL || | | 56 || 5 || {{cellcolors|#d9f|#fff}} P52 || WIFI_CTRL || ? || 10k resistor to GND, and to wifi/BT module. See: [[Media:KTE-001_wifitraces.jpg|wifi/BT 10x7 pinout]] or [[Media:REX-001_wifitraces.jpg|wifi/BT 9x7 pinout]] || Vary || 3.3V | ||
|- | |- | ||
| 57 || 5 || {{cellcolors|#a74}} P53 || UART0_RxD || {{pini}} || Connected to [[Service_Connectors#CN.3F.3F.3F.3F|Service Connector 3rd Gen.]] pin 11 (UART-TTL terminal Receive) through a missing resistor<br>Connected to [[PCI]] [[Media:PCI connector JSD-001 SB and SC UART.jpg|Connector]] pin 6 through a missing resistor || || | | 57 || 5 || {{cellcolors|#a74}} P53 || UART0_RxD || {{pini}} || Connected to [[Service_Connectors#CN.3F.3F.3F.3F|Service Connector 3rd Gen.]] pin 11 (UART-TTL terminal Receive) through a missing resistor<br>Connected to [[PCI]] [[Media:PCI connector JSD-001 SB and SC UART.jpg|Connector]] pin 6 through a missing resistor || || | ||
| Line 175: | Line 175: | ||
| 58 || 5 || {{cellcolors|#a74}} P54 || UART0_TxD || {{pino}} || Connected to [[Service_Connectors#CN.3F.3F.3F.3F|Service Connector 3rd Gen.]] pin 10 (UART-TTL terminal Transmit) through a missing resistor<br>Connected to [[PCI]] [[Media:PCI connector JSD-001 SB and SC UART.jpg|Connector]] pin 4 through a missing resistor || Vary || 3.3V | | 58 || 5 || {{cellcolors|#a74}} P54 || UART0_TxD || {{pino}} || Connected to [[Service_Connectors#CN.3F.3F.3F.3F|Service Connector 3rd Gen.]] pin 10 (UART-TTL terminal Transmit) through a missing resistor<br>Connected to [[PCI]] [[Media:PCI connector JSD-001 SB and SC UART.jpg|Connector]] pin 4 through a missing resistor || Vary || 3.3V | ||
|- | |- | ||
| 59 || 5 || P55 || || | | 59 || 5 || P55 || || ? || Connected to [[South Bridge]] [[CXD9963GB]] pad S19 || || 3.3V | ||
|- | |- | ||
| 60 || 5 || P56 || || | | 60 || 5 || P56 || || ? || Connected to [[South Bridge]] [[CXD9963GB]] pad V22. And in line 47ohms || || 3.3V | ||
|- | |- | ||
| 61 || 5 || P57 || || | | 61 || 5 || P57 || || ? || Connected to [[South Bridge]] [[CXD9963GB]] pad U18 || || 3.3V | ||
|- | |- | ||
| 62 || 1 || {{cellcolors|#33f|#e77}} P17 || RSX_VINTE0<br>VD_VINT0 || {{pini}} || Connected to [[RSX]] pad AR22 ([[Template:RSX pad layout 41x41|41x41 layout]]), or pad <abbr title="Unknown>UNK</abbr> ([[Template:RSX_pad_layout_34x34|34x34 layout]]) through a 10k resistor || || 1.5V | | 62 || 1 || {{cellcolors|#33f|#e77}} P17 || RSX_VINTE0<br>VD_VINT0 || {{pini}} || Connected to [[RSX]] pad AR22 ([[Template:RSX pad layout 41x41|41x41 layout]]), or pad <abbr title="Unknown>UNK</abbr> ([[Template:RSX_pad_layout_34x34|34x34 layout]]) through a 10k resistor || || 1.5V | ||
| Line 199: | Line 199: | ||
| 70 || data-sort-value="19"| || {{cellcolors|#f33|#fff}} AV<span style="font-size:60%;">REF1</span> || || {{pin}} || || || 1.5V | | 70 || data-sort-value="19"| || {{cellcolors|#f33|#fff}} AV<span style="font-size:60%;">REF1</span> || || {{pin}} || || || 1.5V | ||
|- | |- | ||
| 71 || 11 || P110/ANO0 || || | | 71 || 11 || P110/ANO0 || || ? || Connected to a testpad near SC || || | ||
|- | |- | ||
| 72 || 11 || {{cellcolors|#33f|#e77}} P111/ANO1 || RSX_INT || {{pini}} || Connected to [[RSX]] pad AY7 ([[Template:RSX pad layout 41x41|41x41 layout]]), or pad <abbr title="Unknown>UNK</abbr> ([[Template:RSX_pad_layout_34x34|34x34 layout]]). Related with [[Syscon_Error_Codes|Error Code 1802]] || || 1.5V | | 72 || 11 || {{cellcolors|#33f|#e77}} P111/ANO1 || RSX_INT || {{pini}} || Connected to [[RSX]] pad AY7 ([[Template:RSX pad layout 41x41|41x41 layout]]), or pad <abbr title="Unknown>UNK</abbr> ([[Template:RSX_pad_layout_34x34|34x34 layout]]). Related with [[Syscon_Error_Codes|Error Code 1802]] || || 1.5V | ||
| Line 231: | Line 231: | ||
| 82 || 15 || {{cellcolors|#33f|#e77}} P150 || SYS_THR_ALRT<br>THERMAL_OVERLOAD || {{pini}} || Connected to [[CELL BE|CELL]] pad <abbr title="Unknown>UNK</abbr> (1308 layout), or pad <abbr title="Unknown>UNK</abbr> (1359 layout) through a <abbr title="CELL switches the transistor to connect this syscon pin to GND">NPN 50V@100mA transistor</abbr>. Related with [[Syscon_Error_Codes|Error Code 1200 ?]]<br>Connected to a testpad || Vary || | | 82 || 15 || {{cellcolors|#33f|#e77}} P150 || SYS_THR_ALRT<br>THERMAL_OVERLOAD || {{pini}} || Connected to [[CELL BE|CELL]] pad <abbr title="Unknown>UNK</abbr> (1308 layout), or pad <abbr title="Unknown>UNK</abbr> (1359 layout) through a <abbr title="CELL switches the transistor to connect this syscon pin to GND">NPN 50V@100mA transistor</abbr>. Related with [[Syscon_Error_Codes|Error Code 1200 ?]]<br>Connected to a testpad || Vary || | ||
|- | |- | ||
| 83 || 2 || P27/ANI7 || || | | 83 || 2 || P27/ANI7 || || ? || Connected to [[switch boards|Switch board]] power switch ? (POW_SW?) || 3.3V || 3.3V | ||
|- | |- | ||
| 84 || 2 || P26/ANI6 || || | | 84 || 2 || P26/ANI6 || || ? || Connected to [[switch boards|Switch board]] eject switch ? (EJECT_SW?). And to a testpad || || | ||
|- | |- | ||
| 85 || 2 || {{cellcolors|#d9f|#fff}} P25/ANI5 || || | | 85 || 2 || {{cellcolors|#d9f|#fff}} P25/ANI5 || || ? || 10K resistor to GND, to testpad, and to 100ohms resistor to Wifi/BT module. (BT_WAKEON ? or BT_RESET ?) See: [[Media:KTE-001_wifitraces.jpg|wifi/BT 10x7 pinout]] or [[Media:REX-001_wifitraces.jpg|wifi/BT 9x7 pinout]] || || | ||
|- | |- | ||
| 86 || 2 || {{cellcolors|#d9f|#fff}} P24/ANI4 || || | | 86 || 2 || {{cellcolors|#d9f|#fff}} P24/ANI4 || || ? || 10K resistor to GND, to testpad, and to 100ohms resistor to Wifi/BT module. (BT_WAKEON ? or BT_RESET ?) See: [[Media:KTE-001_wifitraces.jpg|wifi/BT 10x7 pinout]] or [[Media:REX-001_wifitraces.jpg|wifi/BT 9x7 pinout]] || || | ||
|- | |- | ||
| 87 || 2 || P23/ANI3 || || | | 87 || 2 || P23/ANI3 || || ? || || || 3.3V | ||
|- | |- | ||
| 88 || 2 || P22/ANI2 || || | | 88 || 2 || P22/ANI2 || || ? || Connected to [[Bluray Drive]] [[Media:BD-460_boards_connectors.jpg|8-pins connector]] pin 8 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or <strike>DISC_IN or DISC_PHOT_LED</strike>), and to a testpad ?. See: [[Template:Syscon_pinout_LQFP_128_pins|pin 115]] || || | ||
|- | |- | ||
| 89 || 2 || P21/ANI1 || || | | 89 || 2 || P21/ANI1 || || ? || Connected to [[Bluray Drive]] [[Media:BD-460_boards_connectors.jpg|8-pins connector]] pin 7 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or <strike>DISC_IN or DISC_PHOT_LED</strike>), and to a testpad ?. See: [[Template:Syscon_pinout_LQFP_128_pins|pin 116]] || || 3.3V | ||
|- | |- | ||
| 90 || 2 || P20/ANI0 || || | | 90 || 2 || P20/ANI0 || || ? || Connected to [[Bluray Drive]] [[Media:BD-460_boards_connectors.jpg|8-pins connector]] pin 6 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or <strike>DISC_IN or DISC_PHOT_LED</strike>), and to a testpad ?. See: [[Template:Syscon_pinout_LQFP_128_pins|pin 117]] || 3.3V || 3.3V | ||
|- | |- | ||
| 91 || 13 || P130 || ACDC_STBY ? || {{pino}} || Enable PSU 12v power rail ? || || 3.3V | | 91 || 13 || P130 || ACDC_STBY ? || {{pino}} || Enable PSU 12v power rail ? || || 3.3V | ||
|- | |- | ||
| 92 || 13 || P131/TI06/TO06 || || | | 92 || 13 || P131/TI06/TO06 || || ? || Connected to voltage regulator [[Talk:Regulators|Mitsumi 348A]] pins 2 and 7 ?<br>Connected to [[Connectors#HDMI_Out| HDMI connector]] pin 18 (+5V output) through a <abbr title="Labeled ARO1A, located next to the HDMI connector, it have a thick copper trace for a voltage of the HDMI connector)>transistor</abbr> ? || || 3.3V | ||
|- | |- | ||
| 93 || 0 || {{cellcolors|#77f|#ff0}} SCL10 || DVE_I2C_SCL || {{pino}} || Connected to [[MultiAV|Digital Video Encoder]] [[CXM4027R]] pin 35 || || 3.3V | | 93 || 0 || {{cellcolors|#77f|#ff0}} SCL10 || DVE_I2C_SCL || {{pino}} || Connected to [[MultiAV|Digital Video Encoder]] [[CXM4027R]] pin 35 || || 3.3V | ||
| Line 255: | Line 255: | ||
| 94 || 0 || {{cellcolors|#77f|#ff0}} SDA10 || DVE_I2C_SDA || {{pinio}} || Connected to [[MultiAV|Digital Video Encoder]] [[CXM4027R]] pin 36 || || 3.3V | | 94 || 0 || {{cellcolors|#77f|#ff0}} SDA10 || DVE_I2C_SDA || {{pinio}} || Connected to [[MultiAV|Digital Video Encoder]] [[CXM4027R]] pin 36 || || 3.3V | ||
|- | |- | ||
| 95 || 0 || P02/SO10/TxD1 || || | | 95 || 0 || P02/SO10/TxD1 || || ? || to pin 12 bdrom port ? (DISC_IN or DISC_PHOT_LED ?) || || 3.3V | ||
|- | |- | ||
| 96 || 0 || P01/TO00 || || | | 96 || 0 || P01/TO00 || || ? || Connected to [[HDMI]] controller [[MN8647091]] pin 93 ??? || || 1.5V | ||
|- | |- | ||
| 97 || 0 || P00/TI00 || || | | 97 || 0 || P00/TI00 || || ? || || || | ||
|- | |- | ||
| 98 || 14 || {{cellcolors|#246|#fff}} TO07 || FANPWM0 || {{pino}} || Connected to the [[Cooling|FAN]] grey wire (PWM duty) || || 0.8V | | 98 || 14 || {{cellcolors|#246|#fff}} TO07 || FANPWM0 || {{pino}} || Connected to the [[Cooling|FAN]] grey wire (PWM duty) || || 0.8V | ||
|- | |- | ||
| 99 || 14 || P144/SO20/TxD2 || || | | 99 || 14 || P144/SO20/TxD2 || || ? || to pin 17 on bdrom port ? (DISC_IN or DISC_PHOT_LED ?) || || 3.3V | ||
|- | |- | ||
| 100 || 14 || {{cellcolors|#77f|#ff0}} SDA20 || HDMI_I2C_SDA || {{pinio}} || Connected to [[HDMI]] controller [[MN8647091]] pin 29 || 0 || | | 100 || 14 || {{cellcolors|#77f|#ff0}} SDA20 || HDMI_I2C_SDA || {{pinio}} || Connected to [[HDMI]] controller [[MN8647091]] pin 29 || 0 || | ||
|}</div><noinclude>[[Category:Templates]]</noinclude> | |}</div><noinclude>[[Category:Templates]]</noinclude> | ||
Revision as of 20:30, 18 June 2022
Pinout
| Pin | Port | Name | Type | Description | Voltages | ||
|---|---|---|---|---|---|---|---|
| NEC/Renesas | Sony/Custom | Stby | Runn | ||||
| 1 | 14 | SCL20 | HDMI_I2C_SCL |  |
Connected to HDMI controller MN8647091 pin 27 | 0 | 3.3V |
| 2 | 14 | P141/PCLBUZ1/INTP7 | ? | Connected to South Bridge CXD9963GB pad AA17 (SB_RESET ?, or SB_CGRST ?) | |||
| 3 | 14 | INTP6 | SB_INT | ? | Connected to South Bridge CXD9963GB pad W22 | 3.3V | |
| 4 | 12 | EXLVI |  |
Connected to Power Supply main +12V rail through a resistor and divider. Related with Error Code 3001 ? | 1.5V | ||
| 5 | 4 | P47/INTP2 | ? | Connected to HDMI controller MN8647091 pin 94 | |||
| 6 | 4 | TO05 | BUZZER | |
Connected to Buzzer- through a NPN 50V@100mA transistor | 3.3V | |
| 7 | 4 | P45/SO01 | ? | Connected to bdrom IC pin 11 (Bluray Drive controller CXD5132R-1 ? or...) | 3.3V | ||
| 8 | 4 | P44/SI01 | THR_I2C_SDA |  |
Connected to TMP411A pin 7 through a 47ohm resistor (CELL Temperature Monitor, data) Connected to TMP411B pin 7 through a 47ohm resistor (RSX Temperature Monitor, data) Connected to ISL6331 pin 22 (Unknown Temperature sensor, data). And a testpad |
3.3V | 3.3V |
| 9 | 4 | P43/SCK01 | THR_I2C_SCL | |
Connected to TMP411A pin 8 (CELL Temperature Monitor, clock) Connected to TMP411B pin 8 (RSX Temperature Monitor, clock) Connected to ISL6331 pin 23 (Unknown Temperature sensor, clock). And a testpad |
3.3V | 3.3V |
| 10 | 4 | P42/TI04/TO04 | ? | Connected to South Bridge CXD9963GB pad AA18 (SB_RESET ?, or SB_CGRST ?) | 3.3V | ||
| 11 | 4 | TOOL1 | TOOL_CLK | |
Connected to Service Connector 3rd Gen. pin 13 (Tool clock) through a missing resistor | 3.3V | |
| 12 | 4 | TOOL0 | TOOL_DAT | |
Connected to Service Connector 3rd Gen. pin 7 (Tool Data) through a missing resistor | 3.3V | |
| 13 | RESET | RST | |
Connected to Service Connector 3rd Gen. pin 9 through a missing resistor | 3.3V | ||
| 14 | 12 | XT2 | OSCOUT | |
Connected to Crystal 32.768kHz (Subsystem clock) | 1.2V | 1.2V |
| 15 | 12 | XT1 | OSCIN | |
Connected to Crystal 32.768kHz (Subsystem clock) | 0.8V | |
| 16 | FLMD0 | FLASH_MODE | |
Connected to Service Connector 3rd Gen. pin 8 (Flash programming mode) through a missing resistor | 3.3V | 3.3V | |
| 17 | 12 | X2 | XTAL | |
Connected to Crystal marked "ED" or "EU" (Main system clock) | ||
| 18 | 12 | X1 | EXTAL | |
Connected to Crystal marked "ED" or "EU" (Main system clock) | ||
| 19 | REGC | VDDbat |  |
Connected to CR2025 battery + through 2 inverted Schottky 30V@30mA diodes ? 1uF capacitor to ground ? |
2.5V | ||
| 20 | VSS | GND | |
||||
| 21 | EVSS0 | GND | |
||||
| 22 | VDD | 3.3_EVER_B | |
Connected to Mitsumi 463A pin 2 (standby voltage regulator, secondary output power rail) | 3.3V | 3.3V | |
| 23 | EVDD0 | 3.3_EVER_B | |
Connected to Mitsumi 463A pin 2 (standby voltage regulator, secondary output power rail) | 3.3V | 3.3V | |
| 24 | 6 | P60/SCL0 | ? | ||||
| 25 | 6 | P61/SDA0 | ? | ||||
| 26 | 6 | P62 | ? | Connected to ISL IC pin 3 | 2.5V | ||
| 27 | 6 | P63 | ? | Connected to Switch board dual led (Red) through a dual digital NPN transistor EMH1(SOT-563) ? (STBY_LED ?) | 3.3V | ||
| 28 | 3 | P31/TI03/TO03/INTP4 | ACIN_DET ? | ? | pin 4 to wifi5v vreg ic/EN ? | ||
| 29 | 6 | P64 | ? | Connected (indirectly) to a voltage regulator ? (to enable something ?) | 3.3V | ||
| 30 | 6 | P65 | ? | Connected to IDT4227 pin 1 | 3.3V | ||
| 31 | 6 | P66 | MK_I2C_SCL ? | ? | Connected to Texas Instruments-SCEI Clock Generator CDC750 pin 33 | 3.3V | |
| 32 | 6 | P67 | MK_I2C_SDA ? | ? | Connected to Texas Instruments-SCEI Clock Generator CDC750 pin 34 | 3.3V | |
| 33 | 7 | P77/KR7/INTP11 | ? | Connected to voltage regulator Rohm BD3527 pin 12 (enable USB ?) | 3.3V | ||
| 34 | 7 | P76/KR6/INTP10 | ? | Connected to ISL6331 pin 24 | 3.3V | ||
| 35 | 7 | P75/KR5/INTP9 | ? | Connected to South Bridge CXD9963GB pad U19 throught 4k7 resistor | 3.3V | ||
| 36 | 7 | P74/KR4/INTP8 | ? | Connected to ISL6331 pin 20 | 3.3V | ||
| 37 | 7 | P73/KR3 | ? | Connected to Service Connector 3rd Gen. pin 3 Connected to D35236SK pin 6 |
3.3V | ||
| 38 | 7 | P72/KR2 | ? | Connected to D35326SK pin 7 | 3.3V | ||
| 39 | 7 | P71/KR1 | |
Connected to voltage regulator Rohm BD3525 pin 12 (enable something) | 3.3V | ||
| 40 | 7 | P70/KR0 | ? | Connected to Texas Instruments PS53123 pin 10 | 3.3V | ||
| 41 | 0 | P06 | ? | Connected to Texas Instruments PS53123 pin 7 | |||
| 42 | 0 | P05 | ? | Connected to Texas Instruments PS53123 pin 17 | 3.3V | ||
| 43 | EVSS1 | GND | |
||||
| 44 | 8 | P80 | ? | 100K pull up to 3v3 | |||
| 45 | 8 | P81 | |
0ohm resistor to GND | |||
| 46 | 8 | P82 | ? | Connected to HDMI controller MN8647091 pin 95 | 3.3V | ||
| 47 | 8 | P83 | |
0ohm resistor to GND | |||
| 48 | 8 | P84 | ? | Connected to pin1 EN vreg 8D11 (bottom side of power pcb) | 3.3V | ||
| 49 | 8 | P85 | ? | Connected to Texas Instruments PS53123 pin 3 | 3.3V | ||
| 50 | 8 | P86 | ? | Connected to IDT4227 pin 12 | 3.3V | ||
| 51 | 8 | P87 | ? | Connected to power pcb connector | 3.3V | ||
| 52 | 3 | P30/INTP3/RTC1HZ | ? | Connected to ISL6331 pin 21 | 3.3V | ||
| 53 | EVDD1 | 3.3_EVER_B | |
Connected to Mitsumi 463A pin 2 (standby voltage regulator, secondary output power rail) | 3.3V | 3.3V | |
| 54 | 5 | P50 | ? | Connected to ISL6331 pin 25 | 3.3V | ||
| 55 | 5 | P51 | ? | Connected to South Bridge CXD9963GB pad W21. And in line 10k to gnd | |||
| 56 | 5 | P52 | WIFI_CTRL | ? | 10k resistor to GND, and to wifi/BT module. See: wifi/BT 10x7 pinout or wifi/BT 9x7 pinout | Vary | 3.3V |
| 57 | 5 | P53 | UART0_RxD | |
Connected to Service Connector 3rd Gen. pin 11 (UART-TTL terminal Receive) through a missing resistor Connected to PCI Connector pin 6 through a missing resistor |
||
| 58 | 5 | P54 | UART0_TxD | |
Connected to Service Connector 3rd Gen. pin 10 (UART-TTL terminal Transmit) through a missing resistor Connected to PCI Connector pin 4 through a missing resistor |
Vary | 3.3V |
| 59 | 5 | P55 | ? | Connected to South Bridge CXD9963GB pad S19 | 3.3V | ||
| 60 | 5 | P56 | ? | Connected to South Bridge CXD9963GB pad V22. And in line 47ohms | 3.3V | ||
| 61 | 5 | P57 | ? | Connected to South Bridge CXD9963GB pad U18 | 3.3V | ||
| 62 | 1 | P17 | RSX_VINTE0 VD_VINT0 |
|
Connected to RSX pad AR22 (41x41 layout), or pad UNK (34x34 layout) through a 10k resistor | 1.5V | |
| 63 | 1 | P16 | RSX_CGRST |  |
This pin is "nerfed" with a 10k resistor to GND in RSX41x41 pad AV6 so syscon is not able to RESET the RSX CG |
0.8V | |
| 64 | 1 | P15 | RSX_VINTE1 VD_VINT1 |
|
Connected to RSX pad AL38 (41x41 layout), or pad UNK (34x34 layout) | 1.5V | |
| 65 | 1 | P14 | RSX_RESET | |
Connected to RSX pad AW5 (41x41 layout), or pad UNK (34x34 layout) | 1.5V | |
| 66 | 1 | P13 | RSX_SPI_CS | |
Connected to RSX pad AW8 (41x41 layout), or pad UNK (34x34 layout) | 1.5V | |
| 67 | 1 | SO00 | RSX_SPI_DO | |
Connected to RSX pad AY8 (41x41 layout), or pad UNK (34x34 layout) | 1.5V | |
| 68 | 1 | SI00 | RSX_SPI_DI | |
Connected to RSX pad BA7 (41x41 layout), or pad UNK (34x34 layout) | ||
| 69 | 1 | SCK00 | RSX_SPI_CLK | |
Connected to RSX pad BA6 (41x41 layout), or pad UNK (34x34 layout) | ||
| 70 | AVREF1 | |
1.5V | ||||
| 71 | 11 | P110/ANO0 | ? | Connected to a testpad near SC | |||
| 72 | 11 | P111/ANO1 | RSX_INT | |
Connected to RSX pad AY7 (41x41 layout), or pad UNK (34x34 layout). Related with Error Code 1802 | 1.5V | |
| 73 | AVREF0 | |
1.2V | ||||
| 74 | AVSS | GND | |
||||
| 75 | 15 | P157 | BE_POWGOOD POWER_GOOD |
|
Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout) Connected to CELL Service Connector CN1001 pad 9 |
1.2V | |
| 76 | 15 | P156 | BE_RESET BE_RESET_AND HARD_RESET |
|
Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout) Connected to CELL Service Connector CN1001 pad 6 and 8 |
1.2V | |
| 77 | 15 | P155 | BE_SPI_DO | |
Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout). Serial Output from Syscon Master to Cell Slave | ||
| 78 | 15 | P154 | BE_SPI_DI | |
Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout). Serial Input from Cell Slave to Syscon Master | ||
| 79 | 15 | P153 | BE_SPI_CLK | |
Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout). 2.5 Mhz SPI Clock | 1.2V | |
| 80 | 15 | P152 | BE_SPI_CS | |
Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout). Chip Select | Vary | 1.2V |
| 81 | 15 | P151 | BE_INT ATTENTION |
|
Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout) through a NPN 50V@100mA transistor. Related with Error Code 1701 | ||
| 82 | 15 | P150 | SYS_THR_ALRT THERMAL_OVERLOAD |
|
Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout) through a NPN 50V@100mA transistor. Related with Error Code 1200 ? Connected to a testpad |
Vary | |
| 83 | 2 | P27/ANI7 | ? | Connected to Switch board power switch ? (POW_SW?) | 3.3V | 3.3V | |
| 84 | 2 | P26/ANI6 | ? | Connected to Switch board eject switch ? (EJECT_SW?). And to a testpad | |||
| 85 | 2 | P25/ANI5 | ? | 10K resistor to GND, to testpad, and to 100ohms resistor to Wifi/BT module. (BT_WAKEON ? or BT_RESET ?) See: wifi/BT 10x7 pinout or wifi/BT 9x7 pinout | |||
| 86 | 2 | P24/ANI4 | ? | 10K resistor to GND, to testpad, and to 100ohms resistor to Wifi/BT module. (BT_WAKEON ? or BT_RESET ?) See: wifi/BT 10x7 pinout or wifi/BT 9x7 pinout | |||
| 87 | 2 | P23/ANI3 | ? | 3.3V | |||
| 88 | 2 | P22/ANI2 | ? | Connected to Bluray Drive 8-pins connector pin 8 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or |
|||
| 89 | 2 | P21/ANI1 | ? | Connected to Bluray Drive 8-pins connector pin 7 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or |
3.3V | ||
| 90 | 2 | P20/ANI0 | ? | Connected to Bluray Drive 8-pins connector pin 6 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or |
3.3V | 3.3V | |
| 91 | 13 | P130 | ACDC_STBY ? | |
Enable PSU 12v power rail ? | 3.3V | |
| 92 | 13 | P131/TI06/TO06 | ? | Connected to voltage regulator Mitsumi 348A pins 2 and 7 ? Connected to HDMI connector pin 18 (+5V output) through a transistor ? |
3.3V | ||
| 93 | 0 | SCL10 | DVE_I2C_SCL | |
Connected to Digital Video Encoder CXM4027R pin 35 | 3.3V | |
| 94 | 0 | SDA10 | DVE_I2C_SDA | |
Connected to Digital Video Encoder CXM4027R pin 36 | 3.3V | |
| 95 | 0 | P02/SO10/TxD1 | ? | to pin 12 bdrom port ? (DISC_IN or DISC_PHOT_LED ?) | 3.3V | ||
| 96 | 0 | P01/TO00 | ? | Connected to HDMI controller MN8647091 pin 93 ??? | 1.5V | ||
| 97 | 0 | P00/TI00 | ? | ||||
| 98 | 14 | TO07 | FANPWM0 | |
Connected to the FAN grey wire (PWM duty) | 0.8V | |
| 99 | 14 | P144/SO20/TxD2 | ? | to pin 17 on bdrom port ? (DISC_IN or DISC_PHOT_LED ?) | 3.3V | ||
| 100 | 14 | SDA20 | HDMI_I2C_SDA | |
Connected to HDMI controller MN8647091 pin 29 | 0 | |
