Editing Progskeet 1.2

[[Category:Hardware]][[Category:Software]]
= Progskeet Support =
[http://www.progskeet.com/mibbit.php Live Support]

= Anouncement =
<div style="border-width: 1px; border-style:dashed; border-color:#000000; padding: 10px; background-color:#FFFFFF; color:#000000; ">[[File:Progskeet 1.2.jpg]]

PROGSKEET V1.2 is in production, release: first week of October (maybe early)

Here some infos in preview:
# Redesign of main board now more small and stable (4 layers)
# Slave board with USB, LED, SWITCH (for memory banks selection)
# FCC cable 15 pins that allow to connect externally the slave board
# Bus SPI on FCC cable for future expansions
# 100% support of WINSKEET
# DLL OPEN library to allow integration in other alternative programs
# 1 Mbit SPI FLASH memory on board

The package content:<br />
1x PROGSKEET V1.2 + SLAVE BOARD<br />
1x ADAPTOR PCB PROGSKEET<br />

The main improve of the new PROGSKEET V1.2 solution will be the support of DUAL NOR / NAND on different consoles.
NOR and NAND CLIPS are not anymore official supported, we decide to move on QSB BOARDS, more cheaper and sure more stable then CLIPS. Soon news also about these accessories.

More infos about specs of new WINSKEET and SOFTWARE will be posted soon.

source: http://www.progskeet.com/forum/viewtopic.php?f=2&t=3964</div>

== Overview ==
[JTAG] <-JTAG 15pin-> J2 [Progskeet 1.2] <-SPI/USB/switchlines 50pin-> J3 [SlaveBoard] <-SPI-> [AdaptorBoard] <-Flashbus-> [QuickSolderBoard]

===J2===
JTAG, 15 pins, pinout (bottom 2): http://www.ps3devwiki.com/images/f/f1/Injectus-jtag-bottompads.png

===J3===
Slaveboard/Adaptorboard connector, 50 pins

===JTAG Pinout===
For FLASH FPGA without flatcable (normally used with Infectus) but soldered, this is the JTAG pinout [[File:Progkeet 1.2 - JTAG.jpg|200px|thumb|left|http://oi47.tinypic.com/s5d8g1.jpg]]
TCK TDO TRST GND<br />
TDI TMS VJTAG VCC
<br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br />

== Bitstreams ==
{{Bitstreams_1.2/1.21}}

== Injectus and Updating Bitstreams ==

# Install the Infectus driver for Injectus --> connect only the Injectus via usb to PC
# Disconnect the Injectus and connect it via 15 pin cable to the Progskeet 1.2, then connect it to the PC.<br />Load the Bitstream <!--// (http://www.progskeet.com/forum/viewtopic.php?f=9&t=4064) //--> with the Infectus Programmer.
# When it´s done disconnect it from the PC and connect the Slaveboard instead of the Injectus. Then connect it to the PC.<br />Install the driver manually.

If it´s done, it will look like this:
<gallery>
File:Progskeet_1.2_Injectus-01.jpg|Progskeet 1.2 - Injectus - 01
File:Progskeet_1.2_Injectus-02.jpg|Progskeet 1.2 - Injectus - 02
File:Progskeet_1.2_Injectus-03.jpg|Progskeet 1.2 - Injectus - 03
</gallery>

== Quick Solder Boards (QSB) ==
[[File:Qsb jsd 001.png|200px|thumb|left|Progskeet - Quick Solder Board (QSB) for JSD-001 (NOR layout4 - SUR-001, JTP-001, JSD-001, KTE-001)]]<br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br />

= Support =
If you have any question (pinout/schematics, availability, shops/resellers, guides/manual/howtos, parts, software flashers, bitstreams, libraries etc), join IRC ef.net #progskeet-support

== Production (lack off) Quality ==
[[File:Progskeet 1.2-production errors.jpg|200px|thumb|left|Progskeet 1.2 - production errors]]

=== Detection issue ===
Sometimes Infectus doesn't detect several progskeets. There is production error. 
Seems, I fixed it with the help of untrax from #progskeet-support <br>
Manual:<br>
1) Desoldered U4 http://tinypic.com/view.php?pic=i5rp53&s=6 - you can see short between two point under U4<br>
2) Remove short, points should not touch each other - http://tinypic.com/view.php?pic=10y13ew&s=6 (hard to see but they are separated) <br>
3) Soldered U4 back, there is should be 2-3 mm between board and chip - http://tinypic.com/view.php?pic=34ornls&s=6<br>
Now Infectus detected my Progsteet, and I am able to update bitstream.<br>

== Community fixing of the Progskeet 1.2 "black turd" ==
[http://www.ps3hax.net/showthread.php?t=48799 Make ProgSkeet v1.2 WORK as a v1.1]
* [http://www.ps3hax.net/showpost.php?p=505241&postcount=20 updated PCB]