Editing Talk:Progskeet 1.0 / 1.1

== PADS ==

=== R7 / R8 ===
<div style="float:right">[[File:Progskeet-R7-R8_explaination-sketch4.jpg|200px|thumb|left|Sketch with R7/R8 explaination]]</div>

{| class="wikitable"
|-
! R7 !! R8 !! 
|-
| open || open || Configuration does not work with PS3.  Stock Progskeet.  Actel never powered.
|-
| open || closed || Actel powered by USB
|-
| closed || open || Actel powered by 3.3 line
|-
| closed || closed || DO NOT DO when using 3.3V wire ánd PS3 PSU powered.  Will blow progskeet by Actel being powered by USB and enabling 3.3 output.  
|-
|}

=== R9 / R10 / R11 / R12 ===
{| class="wikitable sortable"
|-
! R9 !! R10 !! R11 !! R12 !! 
|-
| {{Yes}} || {{No}} || {{Yes}} || {{No}} || 3 - 3.3V Flash
|-
| {{No}} || {{Yes}} || {{No}} || {{Yes}} || 1.5 - 1.8V Flash
|-
| {{Yes}} || {{Yes}} || {{Yes}} || {{Yes}} || BAD Configuration
|-
| {{No}} || {{No}} || {{No}} || {{No}} || BAD Configuration
|-
|}

=== Short guides ===
Best praxis:
  NAND : method [D]   /    NOR : method [A]

==== [A] using PS3 PSU and Progskeet powered by USB ====
<div style="float:right">[[File:Ps3+usb.jpg|200px|thumb|left|Progskeet - PS3+USB]]</div>
<div style="border-width: 1px; border-style:dashed; border-color:#000000; padding: 10px; background-color:#FFFFFF; color:#000000; ">
'''Progskeet:'''
* ignore R7, close R8, close R9, open R10, close R11, open R12. do not use 3.3V wire from PS3 to Progskeet 3.3V pad

'''PS3:''' 
* see above: do not use 3.3V wire

'''Usage:'''
* Power on console, halt by inserting USB to progskeet, dump CFI/autodetect, and when that is valid, dump flash and [[Validating flash dumps|validate]].

'''Normal mode:'''
* Disconnect USB from PC to Progskeet

'''Note:''' 
* You need a powersupply, a power/reset board and cooling with fan
</div>

==== [B] using Progskeet powered by USB with Flash powered by Progskeet regulator ====
<div style="float:right">[[File:Usb-only.jpg|200px|thumb|left|Progskeet - USB-only]]</div>
<div style="border-width: 1px; border-style:dashed; border-color:#000000; padding: 10px; background-color:#FFFFFF; color:#000000; ">
'''Progskeet:'''
* close R7, close R8, close R9, open R10, close R11, open R12. use 3.3V wire from Progskeet 3.3V pad to PS3 flash

'''PS3:'''
* see above: use 3.3V wire

'''Usage:'''
* Connect Progskeet USB, dump CFI/autodetect, and when that is valid, dump flash and [[Validating flash dumps|validate]].

'''Normal mode:'''
* Open R7 or discontinue 3.3V line

'''Note:'''
* This method is least reliable because PS3 board drains 1200-1800mA while Progskeet can only supply 300-500mA.
</div>

==== [C] using PS3 PSU and Progskeet powered by Console ====
<div style="float:right">[[File:Console-only.jpg|200px|thumb|left|Progskeet - Console-only]]</div>
<div style="border-width: 1px; border-style:dashed; border-color:#000000; padding: 10px; background-color:#FFFFFF; color:#000000; ">
'''Progskeet:'''
* switch R7, open R8, close R9, open R10, close R11, open R12. use 3.3V wire from Progskeet 3.3V pad to PS3 flash

'''PS3:'''
* see above: use 3.3V wire

'''Usage:'''
* Power on console, halt by switching R7 on, dump CFI/autodetect, and when that is valid, dump flash and [[Validating flash dumps|validate]].

'''Normal mode:'''
* Open R7 or discontinue 3.3V line

'''Note:'''
* This is the old/archaic switched method.
* You need a powersupply, a power/reset board and cooling with fan
</div>

==== [D] using ATX PSU and Progskeet powered by USB ====
<div style="float:right">[[File:Usb+atx.jpg|200px|thumb|left|Progskeet - USB+ATX]]</div>
<div style="border-width: 1px; border-style:dashed; border-color:#000000; padding: 10px; background-color:#FFFFFF; color:#000000; ">

'''Progskeet:'''
* ignore R7, close R8, close R9, open R10, close R11, open R12. do not use 3.3V wire from PS3 to Progskeet 3.3V pad

'''ATX:'''
* connect +3.3V and GND to flash

'''Usage:'''
* Power on ATX PSU, dump CFI/autodetect, and when that is valid, dump flash and [[Validating flash dumps|validate]].

'''Normal mode:'''
* Discontinue 3.3V line
</div>

==== [E] using ATX PSU and Progskeet powered by ATX ====
<div style="float:right">[[File:Atx-only.jpg|200px|thumb|left|Progskeet - ATX-only]]</div>
<div style="border-width: 1px; border-style:dashed; border-color:#000000; padding: 10px; background-color:#FFFFFF; color:#000000; ">
'''Progskeet:'''
* close R7, open R8, close R9, open R10, close R11, open R12. use 3.3V wire from PS3 to Progskeet 3.3V pad

'''ATX:'''
* connect +3.3V and GND to flash

'''Usage:''' 
* Power on ATX PSU, dump CFI/autodetect, and when that is valid, dump flash and [[Validating flash dumps|validate]].

'''Normal mode:'''
* Open R7 and Discontinue 3.3V line
</div>

=== Solder vs Solderless ===
PAD I/O usage, Solder versus Solderless bitstream

{| class="wikitable"
|-
! NAND1 !! Solder<br />bitstream<br />Progskeet !! SL NAND<br />bitstream<br />Progskeet !! Remarks
|-
| RB || rdy || gp5 || 
|-
| RE || oe || gp1 ||
|-
| CE || gp3 || gp2 ||
|-
| CLE || gp0 || we ||
|-
| ALE || gp1 || rdy ||
|-
| WE || we || gp0 ||
|-
| WP || gp2 || gp3 ||
|-
|}
Nand1 IO: dq0 to dq7
{| class="wikitable"
|-
! NAND2 !! Solder<br />bitstream<br />Progskeet !! SL NAND<br />bitstream<br />Progskeet !! Remarks
|-
| RB || gp13 || a15 || 
|-
| RE || gp15 || a19 ||
|-
| CE || gp9 || a18 ||
|-
| CLE || gp12 || a22 ||
|-
| ALE || gp11 || a21 ||
|-
| WE || gp14 || a20 ||
|-
| WP || gp10 || a17 ||
|-
|}
Nand2 IO: dq8 to dq15

== Why does it give verification errors when writing or halt/freeze when dumping? ==
* Bad wiring
** 30AWG (bad) instead of 26AWG (ok) for NOR
** Too long wires (>15cm)
* Bad PC / USB chipset, just try an old PC with Windows XP/Linux
** Bad USB cable
* Interference
* Bus not free / Halted incorrect
* Power drops
* Bad grounding



=== Help sheet ===
These questions will be asked online anyhow, so you might consider posting them on http://pastie.org/pastes/new prefilled in:
<pre>username: 

## Console SKU / motherboard / Flash type ?

## Wire length / thickness ?

## What Winskeet version ?

## What driver (libusb0 or WinUSB) ?

## What preset/settings ?

## Tried generic slowest to the letter ? (http://www.ps3devwiki.com/wiki/Talk:Hardware_flashing#Generic_slowest_safe_method)

## How are you halting ? (10sec and then halting, did you try shorter ?)

## How are you powering ?

## Is R8 and R7 open or closed ?

## Is R9+R11 or R10+R12 closed ?

## Uploaded pictures or dump ? (http://www.mirrorcreator.com/)
</pre>




== External Tutorials ==
* [http://www.progskeet.com/forum/viewtopic.php?f=3&t=3749 Nand Dumping process for cok-002w/002 - by avati] (does not cover [[Validating flash dumps]] fully though)