Editing Teensy++ 2.0

= Teensy 2.0 ++ Powering =

== Powering option 1 (voltage regulator, Teensy powered by USB) ==
Install the 3.3V voltage regulator available at pjrc.com! 5V trace has to be cut and 3V pads have to be shorted!
Please refer to https://www.pjrc.com/teensy/3volt.html

DON'T CONNECT THE VCC SOLDER PADS TO ANYTHING!

== Powering option 2 (external power, Teensy powered by console) ==
Connect Teensy's VCC solder pad to PS3's 3.3V supply (see connection diagram). 5V trace has to be cut and
3V pads have to be shorted!
Please refer to https://www.pjrc.com/teensy/3volt.html

DON'T INSTALL VOLTAGE REGULATOR!

= Teensy 2.0 ++ Downloads =

== NORway ==
Used to analyze dumps and also contains hex files to program the Teensy itself.

* [https://github.com/hjudges/NORway NORway git]
** [http://ps3devwiki.com/files/flash/Tools/NORway/NORway-0.5b4.zip NORway-0.5b4.zip]

=== Mac OS-X patch ===
if you are on Mac OS-X and having problems with timeouts:
 <MikeM64> hahaha, it's a dirty fix, but it seems to work XD
 <MikeM64> lemme compile diffs, I got perfect writes happening on my mac now
 <MikeM64> 10 writes and 2 timeouts; not bad. better than 20 timeouts / write
 <MikeM64> http://pastie.org/8570558 if anyone needs it

== NANDway ==
Project home:
* https://github.com/hjudges/NORway (previously https://github.com/Effleurage/NORway-and-NANDway but now merged in main git)

precompiled by judges : http://www.mediafire.com/?i5y1mhhh5lz62xu

== Teensy NAND Pinout ==

[[File:TeensyNAND.png]]

Notes:
* WP: When the NANDs are mounted on the PS3 motherboard - the WP controllines are already connected to +3.3V. If Teensy is used for NANDs on the PS3 motherboard - the WP wire for each NAND can be discarded.
* Vcc: Teensy 3.3V regulator cannot power the NANDs on the PS3. The drain of the motherboard summed by the other peripherals draw too much current (~1.8A). The NANDs can be powered from external 3.3V power supply like ATX power supply (the orange 3.3V line of the ATX main connector).

== NANDway usage ==
<pre>NANDWay.py Serial-Port 0/1 Command

  Serial-Port  Name of serial port to open (eg. COM1, COM2, /dev/ttyACM0, etc)
  0/1  NAND id number: 0-NAND0, 1-NAND1
  Commands:
  *  dump Filename [Offset] [Length]
     dumps to Filename at [Offset] and [Length]
  *  vwrite/write Filename [Offset] [Length]
     Flashes (v=verify) Filename at [Offset] and [Length]
  *  vdiffwrite/diffwrite  Filename Diff-file
     Flashes (v=verify) Filename using a Diff-file
  *  release
     Releases TRISTATE, so that the PS3 can boot
  *  bootloader
     Enters Teensy's bootloader mode (for Teensy reprogramming)
     Notes: 1) All offsets and lengths are in hex
            2) The Diff-file is a file which lists all the changed
               offsets of a dump file. This should increase flashing
               time dramatically.

Examples:

  NANDWay.py COM1
  NANDWay.py COM1 0 dump d:\myflash.bin
  NANDWay.py COM1 1 dump d:\myflash.bin 3D a0
  NANDWay.py COM1 0 write d:\myflash.bin
  NANDWay.py COM3 1 write d:\myflash.bin
  NANDWay.py COM3 1 vwrite d:\myflash.bin 8D A0000
  NANDWay.py COM4 0 diffwrite d:\myflash.bin d:\myflash_diff
  NANDWay.py COM3 1 vdiffwrite d:\myflash.bin d:\myflash_diff
  NANDWay.py COM1 0 release
</pre>

== NORway usage ==
<pre>Usage: %s serialport [command] [filename] [address]
    
serialport  Name of serial port to open (eg. COM1, COM2, /dev/ttyACM0, etc)
command     dump       Reads entire NOR to [filename]
            erase      Erases one sector (128KB) at [address]
            write      Flashes (read-erase-modify-write-verify) [filename]
                       at [address] to NOR
            writeimg   Same as write, but prepend a 16-byte length header
                       [address] is required
            program    Flashes (erase-write-verify) [filename]
                       at [address] to NOR
            release    Releases NOR interface, so the PS3 can boot
filename    Filename for [dump|write|writeimg|program]
address     Address for [erase|write|writeimg|program]
            Default is 0x0, address must be aligned (multiple of 0x20000)
</pre>

== Drivers & UDEV Rules ==
The Teensy 2.0++ needs windows drivers and linux udev rules to be recognized fully as it was meant to.
* [http://www.pjrc.com/teensy/usb_serial.html Teensy Drivers from PJRC.com]
** [http://ps3devwiki.com/files/flash/Tools/NORway/drivers/ filemirror]

= Hardware Picture =
<table style="width:100%;">
   <tr>
      <td>[[File:Teensy2.0++.jpg|600px|thumb|left|Teeny++ Dev Board]]</td>
   </tr>
</table>

= Installation Requirements =

You are going to need a lot parts to accomplish such a task.  This takes a lot of patience, and steady hands.<br>
This is a difficult installation!  If a part is not needed below it will be specified per model so check there as well.<br>

== Parts ==
The following items are required to perform the installation of the Teensy++ to most PS3 consoles.

1x Sony Playstation 3 Console<br>
1x Teensy 2.0 ++<br>
1x Dremel Tool (Not needed on some models)<br>
1x Drill<br>
1x Roll of Double Sided Foam Tape<br>
1x 30AWG Kynar Wire or 26 AWG Kynar Wire.  (Few have reported 30AWG may be too small and has interference but does work if done well.)<br>
1x Torque 10(T-10) Screwdriver<br>
1x Torque 8 (T-8) Screwdriver<br>
1x Regular Phillips Head Screwdriver<br>
1x Solder (Can be leaded or no-lead)<br>
1x Soldering Iron  (Radioshack 15-30 Watt Will Work.)<br>
1x Bottle Of Flux No-Clean<br>
1x Bottle Of 99% Isoprobyl Alcohol<br>
1x Box of Q-Tips  (For spreading flux and alcohol where needed.)<br>
1x Pair Of Steady Hands  (Not Joking.  Tremor Fingers will not cut it. You are soldering 40+ points and all must be done very well.)<br>
1x Good Lighting  (Either very well lighted room, or a Lamp.  You need to be able to check your work.)<br>
1x Magnifying Glass  (To check your soldering joints for cold solders.)<br>
1x Patience.<br>

As you can see it requires a lot of materials to perform this kind of job.  If you do not already have the parts for this kind of project, it will probably be cheaper to pay someone else to do it and ship it to and from them.  Also if you are not confident in your soldering technique, it is a very realistic possibility that you will ruin your Playstation 3 Console during this process as there are a LOT of soldering joints that need to be perfectly made.

== Teensy Install Notes by CECH Model ==
First open the PS3.  Follow youtube videos to learn how (Just search).

Once opened, look at the motherboard model printed there.  Depending on which model you have follow the case modifications below to install teensy.

There are two methods to use a Teensy 2.0++ Flasher.  

1.) Install while the PS3 is somewhat opened still with everything plugged in.  (Be careful of shorts.)

2.) Internal Case Modifications.  This is the best way to go as you can install the teensy inside of the PS3 for later use.  This is the advantage of using a Teensy 2.0++ because it's just small enough to install inside the PS3 with a little case modification.  Other flashers are generally too large to do this with the PS3 closed up.  You will find there is just no room for it.

=== COK-001, COK-002, COK-002W, SEM-00 1===

I used the image for the Progskeet, along with an image of which Progskeet pin(GP1 etc.) corresponds to which NAND chip pin name (WP, ALE, CLE, I/O1 etc.) to create a diagram of which testpoint on the mainboard goes to which leg of the NAND chips made by Samsung.

[http://ptodorov.com/files/diy/cok002-NAND-TEENSY.jpg Diagram for wiring Teensy++ 2.0 to a PS3 COK-002 mainboard]

So now you can use this diagram not only for downgrading/dumping/writing the NANDs with a Teensy++ 2.0 board, but with any other board available on the Internet.

'''Important:''' You must provide a stable 3.3V PSU to both the PS3 board and the Teensy, and don’t forget to unite the GNDs. You can use any PSU which outputs 3.3V @ 1.8A+, the easiest option will be to use a PC PSU.

=== DIA-001, DIA-002 ===
Parts not needed?   Submitter please list here.<br>


==== Installation and Case Modification ====
This installation the case was not modified.  It was flashed while opened, and removed.
<table style="width:100%;">
   <tr>
      <td>[[File:IMG 0194.JPG|250px|thumb|left|Teensy++ tucked away below where the psu sits, usb cable hanging out.]]</td>
      <td>[[File:IMG 0193.JPG|250px|thumb|left|Teensy++ soldered to NOR testpoints]]</td>
   </tr>
</table>

=== VER-001 ===

Parts needed? Submitter please list here.<br>


=== Installation and case modification ===
In this installation, the cables were strategically soldered to fit better and not break or short when the power supply was placed, so no external power was needed.
<table style="width:100%;">
   <tr>
      <td>[[File:Soldered_to_teensy.JPG|250px|thumb|left|The shielding was cut with a small dremel to have a more permanent install.]]</td>
      <td>[[File:Soldered_to_teensy_1.JPG|250px|thumb|left|Teensy++ soldered to NOR testpoints]]</td>
      <td>[[File:Wire_placement.JPG|250px|thumb|left|Each pin was carefully bent and were soldered with an idea of where they'd fit between the BD and PSU. Double sided tape was used to hold the teensy 2.0++ in place.]]</td>
      <td>[[File:Wire_mess.JPG|250px|thumb|left|A small port was made for the usd, and a button was later placed next to it for teensy programing]]</td>
   </tr>
</table>

=== DYN-001 ===

Parts not needed - Torque T-10 Screwdriver.  (T-8 IS still needed!)<br>
<br>

==== Installation and Case Modifications ====

Be sure to make a screw map when disassembling the PS3, there are a lot of screws, and you will not remember where they go.

First and Second dremel area.  These 4 pictures show before and after affects and where to dremel on the top side shielding.
<table style="width:100%;">
   <tr>
      <td>[[File:IMAG0109.jpg|250px|thumb|left|DYN-001 Placement Area and first dremel]]</td>
      <td>[[File:IMAG0106.jpg|250px|thumb|left|DYN-001 Wire direction and second dremel]]</td>
      <td>[[File:IMAG0110.jpg|250px|thumb|left|DYN-001 Post dremel for Teensy placement]]</td>
      <td>[[File:IMAG0111.jpg|250px|thumb|left|DYN-001 Teensy fits.  Need to wait until MB is back in shielding before final placement.]]</td>
      
   </tr>
</table>

Third dremel area.  These pictures show before and after affects  and where to dremel on the bottom side shielding.<br>
This helps with interference by running wires outside the shielding instead of inside.  This method has to be done <br>
on these models as unlike JSD-001 Models there are no holes or spaces between the HDD and shielding.  It's connected<br>
on DYN-001 Models.<br><br>
NOTE:  When placing teensy, DO NOT PLACE directly on the shielding.  Make sure you use a strip of double sided foam tape. to act between the shielding and teensy.
<table style = "width:100%;">
   <tr>
      <td>[[File:IMAG0113.jpg|250px|thumb|left|DYN-001 Wire direction and third dremel]]</td>
      <td>[[File:IMAG0117.jpg|250px|thumb|left|DYN-001 Post dremel of bottom shield]]</td>
      <td>[[File:IMAG0119.jpg|250px|thumb|left|DYN-001 Reconstruct shielding and Chip Mounts]]</td>
      <td>[[File:IMAG0123.jpg|250px|thumb|left|DYN-001 Post Wire Job Topside.]]</td>
      <td>[[File:IMAG0125.jpg|250px|thumb|left|DYN-001 Post Wire Job Underside.]]</td>
   </tr>
</table>

Forth and last dremel area.  This is done on the case itself.  The port for the teensy is covered by the HDD cover area.  You will have to take care in cutting open the area.  If you did not spread your wires out evenly on the underside of the shielding, it will create a raised section and the port itself will be too high to reach and may have to dremel higher.  
<table style = "width:100%;">
   <tr>
      <td>[[File:IMAG0136.jpg|400px|thumb|left|DYN-001 Open Port]]</td>
      <td>[[File:IMAG0132.jpg|400px|thumb|left|DYN-001 USB Cable plugged into flasher]]</td>
      <td>[[File:IMAG0143.jpg|400px|thumb|left|DYN-001 HDD + Teensy Cover :)]]</td>
   </tr>
</table>

Notes on Reassembly:
Before putting back the blu-ray drive, carefully bend each wire on the topside flat by hand ONE AT A TIME so you do not break the solder joints on the teensy.  If you do not bend them flat by hand one at a time carefully, the drive could easily undo one of your soldering joints and you will have to start again.  (I managed to do it on the first try.  Did I say that you needed 1x of Patience?  

Testing:
You can test your work before putting the cover top back on.  Just make sure blu-ray and power-supply are connected and everything else before trying.  This is so you know that everything is fitting okay and that the install has worked for you.  Take 3 dumps (Read above on how to take a dump of NOR) and compare them.  Do md5sum and sha1sum, and then try and unpack them with norunpack from f0f tools.  If they all match, and it unpackages, congratulations you have a good dump!

=== JSD-001 ===
No dremel required.  Design of this CECH 2500 series has an opened hole area to put wires through.<br>


==== Installation and Case Modification ====
<table style="width:100%;">
   <tr>
      <td>[[File:install-1.jpg|250px|thumb|left|JSD-001 Teensy Placement.  Mounted using double sided foam tape.]]<br />
          [[File:install-2.jpg|250px|thumb|left|JSD-001 Port cut and drilled to view teensy usb port from outside.]]</td>
      <td>[[File:install-3.jpg|250px|thumb|left|JSD-001 Post wire job from motherboard view with wire wrap.]]<br />
          [[File:install-4.jpg|250px|thumb|left|JSD-001 Teensy placement and wired up. Notice open space.]]</td>
      <td>[[File:JSD-001 testpoints.png|250px|thumb|left|JSD-001 Motherboard NOR Test Points.]]<br />
          [[File:JSD-001, Teensy2.0++ Connection Diagram.jpg|250px|thumb|left|JSD-001, Teensy2.0++ Connection Diagram]]</td>
   </tr>
</table>

=== SUR-001/JTP-001/KTE-001 ===

*** Need submissions...


{{Hardware Flashers}}<noinclude>[[Category:Main]]</noinclude>