Template:Syscon pinout BGA 200 pads: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
Line 214: | Line 214: | ||
| M5 || GBE_RESET || | | M5 || GBE_RESET || | ||
|- | |- | ||
| N4 || SW_5_A || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (+1.2V_RSX_VDDC) | | N4 || SW_5_A || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] pin 29 (+1.2V_RSX_VDDC) | ||
|- | |- | ||
| M4 || SW_9 || | | M4 || SW_9 || |
Revision as of 06:09, 13 October 2022
Pad# | Name | Port | Description |
---|---|---|---|
T2 | BE_INT | Port M Cell Control Line |
Connected to CELL 90nm pad AW19 |
R1 | PM7 | ||
R2 | PM6 | ||
P1 | BE_POWGOOD | Connected to CELL 90nm pad AV20 | |
P2 | BE_RESET | Connected to CELL 90nm pad AW20 | |
N1 | BE_SPI_CLK | Connected to CELL 90nm pad AY13 (SPI Bus) | |
N2 | BE_SPI_DO | Connected to CELL 90nm pad AV13 (SPI Bus) | |
M1 | BE_SPI_DI | Connected to CELL 90nm pad AR13 (SPI Bus) | |
M2 | BE_SPI_CS | Connected to CELL 90nm pad AP13 (SPI Bus) | |
L4 | PL8 | Port N | unused |
L5 | PL7 | ||
K4 | PL6 | ||
K5 | PL5 | ||
J4 | PL4 | ||
J5 | PL3 | ||
H4 | PL2 | ||
H5 | PL1 | ||
H6 | PL0 | ||
A8 | SB_SPI_CLK | Port K | Southbridge SPI Bus |
B8 | SB_SPI_DO | ||
A9 | SB_SPI_DI | ||
B9 | SB_SPI_CS | ||
A10 | DVE_I2C_SCL | ||
B10 | DVE_I2C_SDA | ||
A11 | ACDC_STBY | ||
B11 | PK0 | ||
B5 | PJ7 | Port J | |
A5 | DISC_OUT12_SW | ||
B2 | DISC_OUT8_SW | ||
A2 | DISC_IN | ||
B3 | SW_10 | ||
A3 | SW_0 | Connected to Fujitsu MB39A116PFT pins 9 and 10, who generates +3.3V_MISC and +5V_MISC Connected to Texas Instruments SN105233DBTR pin 10, who generates +1.7_MISC | |
B4 | SW_8_B | +1.5V VDDIO for both AVCG & RSX Analog IO | |
A4 | SW_8_C | Connected to Texas Instruments SN105233DBTR pin 9, who generates +1.8V_RSX_FBVDDQ | |
L16 | SW_PCI | Port I | Connected to Mitsumi MM1591FFBEG pin 5, and Mitsumi MM1593DFBEG pin 5. This voltage regulators generates the power lines named "+1.5V_BRIDGE" and "+3.3V_BRIDGE" to feed CXD9208GP |
L15 | DISC_CHUCK | ||
M16 | DISC_PHOT_LED | ||
M15 | SW_2 | Connected to Texas Instruments TPS51117PWRG4 pin 1 who generates +1.8V_VDD_MEM | |
N16 | DIAG_MODE | ||
N15 | BACKUP_MODE | ||
E6 | HDMI_INT | Port H | |
D6 | VD_CECI0 | ||
E7 | PH5 | ||
D7 | RS_POW_FAIL | ||
E8 | MUL_CHKSTP_IN | ||
D8 | MUL_TRG_IN | ||
E9 | SYS_THR_ALRT | Connected to CELL 90nm pad AP23 | |
D9 | SB_INT | ||
M11 | SW_ATA | Port G | |
N11 | SW_4_A | +1.2V, +1.9V, +3.3V ESW (Ethernet Controller) | |
M10 | XDR_FET_VREF | ||
N10 | XDR_FET_SCK | ||
M9 | BUZZER | ||
N9 | SW_PWM | Unknown output ? (connected to the Switch board) | |
M8 | FANPWM1 | Secondary fan output (non-retail PS3 models only) | |
N8 | FANPWM0 | Primary fan output (all PS3 models) | |
E10 | MUL_CHKSTP_OUT | Port F | |
D10 | MUL_TAG_OUT | ||
E11 | SB_CGRESET | ||
D11 | SB_RESET | ||
E12 | BT_WAKEON | ||
D12 | PF2 BE_VCS_1.25_ON |
COK-001/COK-002 PF2 (Not connected) SEM-001 BE_VCS_1.25_ON | |
E13 | PF1 BE_VCS_1.30_ON |
COK-001/COK-002 PF1 (Not connected) SEM-001 BE_VCS_1.30_ON | |
D13 | SW_1_A | +3.3V_MK_VDD for Clock Synthesizer | |
A12 | EJECT_SW | Port E | |
B12 | POW_SW | ||
A13 | SB_EBUS_RESET | ||
B13 | SB_EBUS_BRDY | ||
A14 | PE3 | ||
B14 | VD_CECI1 | ||
A15 | BE_POW_FAIL | ||
B15 | POW_FAIL | ||
F13 | SW_5_B | Port D | Connected to Rohm BD3520FVM-TR (IC6200) pin 3, who generates +1.2V_RSX_VDDR |
F12 | MK_EN | Connected to clock generator ICS1493G-18LFT (IC5001 pin #16 on COK-001, COK-002, SEM-001) | |
G13 | BEVRM_VID5 | ||
G12 | BEVRM_VID4 | ||
H13 | BEVRM_VID3 | ||
H12 | BEVRM_VID2 | ||
J13 | BEVRM_VID1 | ||
J12 | BEVRM_VID0 | ||
K13 | SW_HDD | Port C | |
K12 | I2CBUS_EN | Connected to TC7WB66FK pins 3 and 7 (IC5005 on SEM-001) through 1K resistor. This chip "duplicates" the MK_I2C_SCL/MK_I2C_SDA bus into a secondary XCG_I2C_SCL/XCG_I2C_SDA bus for the clock reference chip/s | |
L13 | RSXVRM_VID5 | ||
L12 | RSXVRM_VID4 | ||
M13 | RSXVRM_VID3 | ||
M12 | RSXVRM_VID2 | ||
N13 | RSXVRM_VID1 | ||
N12 | RSXVRM_VID0 | ||
T15 | SW_8_A | Port B | Connected to Rohm BD3504FVM-TR pin 3 (IC6304, not IC6602) who generates +1.5V_YC_RC_VDDA (Analog voltage supplies, VDD_A) |
R14 | SW_7_A | +1.0V_BE_VDDC (Cell BE core voltage supply (VDD) then VCS (the core array voltage). Note, the VID values stored on the CELL itself are not available to be read yet. So the default VID of the VRM is used until then. | |
T14 | SW_6 | Connected to Rohm BD3520FVM-TR (IC6303) pin 3 who generates +1.2V_YC_RC_VDDIO (I/O voltage supplies, VDD_IO) for CELL | |
R13 | SW_1_B | +2.5V_LREG_XCG_500_MEM. Analog Voltage for the core PLL of IC5004, Clock Generator used to support the Rambus XDR memory subsystem and Redwood logic interface. | |
T13 | SW_4_B | +5V_USB, +1.8V_SB_PERI, +2.5V_SB_PLL_VDDC | |
R12 | SW_3 | Connected to Rohm BD3520FVM-TR (IC6305) pin 3, who generates +1.2V_SB_VDDC and +1.2V_SB_VDDR | |
T12 | VD_CECO1 | ||
R11 | VD_CECO0 | ||
N7 | STBY_LED | Port A | |
M7 | POW_LED | ||
N6 | AUDIO_MUTE | Uses a transistor, to switch another 2 transistors, that switches pins AOUTA#18 and AOUTB#15 of Cirrus CS4351-CZZR 192 kHz Stereo DAC (pins 9 and 11 of the MultiAV connector) | |
M6 | SW_7_B | ||
N5 | BT_RESET | ||
M5 | GBE_RESET | ||
N4 | SW_5_A | Connected to OnSemi NCP5318FTR2G pin 29 (+1.2V_RSX_VDDC) | |
M4 | SW_9 | ||
J16 | RBB | EEPROM Interface | |
K16 | PI7 | ||
J15 | WCB | ||
K15 | PI6 | ||
E16 | SKB | ||
E15 | PP3 | ||
G16 | DI | ||
G15 | PP2 | ||
H16 | DO | ||
H15 | PP1 | ||
F16 | CSB | ||
F15 | PP0 | ||
H11 | TESTMODE | Reset & Clock | |
B16 | OSCOUT | ||
C16 | OSCIN | ||
D16 | 32KOUT | ||
D15 | 32KIN | ||
T5 | EXTAL | ||
T4 | XTAL | ||
T7 | XXTALO | ||
J11 | RST | ||
R4 | AVSUO | Power Port | Ground |
R5 | AVDUO | +3.3v | |
G6 | AVSS | Ground | |
C2 | AVREF2 | Ground | |
B1 | AVREF1 | +3.3v | |
F7 | AVDD | +3.3v | |
K11 | VSSF | Ground | |
K6 | VSSF | Ground | |
L6 | VDDF | +3.3v | |
G7 | VSS | Ground | |
G8 | |||
G10 | |||
T6 | |||
R6 | |||
T3 | |||
L1 | |||
E1 | |||
C15 | VSSep | EEPROM Ground | |
G11 | VDDep | EEPROM Power +3.3v | |
F11 | VDDbat | +battery | |
H7 | DVDD | +1.8v | |
J10 | |||
K10 | |||
L10 | |||
L11 | |||
R7 | |||
J7 | |||
F8 | VDD3 | +3.3v | |
F10 | |||
H10 | |||
J6 | |||
F6 | |||
D2 | VDD2 | +1.5V_RSX_VDDIO | |
R3 | VDD1 | +1.2V_MC2_VDDIO | |
L2 | VDD0 | +1.2V_MC2_VDDIO | |
A16 | NC | ||
T16 | |||
T1 | |||
A1 | |||
G9 | |||
F9 | |||
L8 | JRTCK | JTAG Interface | |
K8 | JTCK | ||
K9 | JTDO | ||
L9 | JTMS | ||
K7 | JTDI | ||
L7 | JNTAST | ||
A6 | PR3 | Port R | |
B6 | MC_P_OFF_REQ | ||
A7 | MC_ALIVE | ||
B7 | MC_RESERVED1 | ||
R10 | RMC_IN | Port Q | Connected to missing IR receiver in the Switch boards (IR remote control input using SIRC protocol and SERV_SIRCS) |
T11 | PQ5 | ||
T10 | PQ4 | ||
T8 | THR_I2C_SCL | ||
T9 | THR_I2C_SDA | ||
R9 | PQ1 | ||
R8 | RSX_FBVDD_SEL | ||
P16 | UART0_TxD | Port P | Serial Transmit |
P15 | UART0_RxD | Serial Receive | |
R16 | HDMI_I2C_SCL | ||
R15 | HDMI_I2C_SDA | ||
D1 | MK_I2C_SCL | Port O | Connected to clock generator ICS1493G-18LFT (IC5001 pin #46 on COK-001) |
C1 | MK_I2C_SDA | Connected to clock generator ICS1493G-18LFT (IC5001 pin #47 on COK-001) | |
G4 | PO7 | ||
F4 | HDMI_RST0 | ||
G5 | PO5 | ||
F5 | DISC_IN_MECHA | ||
E4 | EJECT_MECHA | ||
D4 | XDR_FET_RST | ||
E5 | GX_VSRST | ||
D5 | XCG_EN | Connected to ICS9218AGLFT and ICS9214DGLFT pin 11 (IC5002, IC5003 and IC5004 on COK-002). Reference clocks for BE, RSX, SB | |
K2 | VD_VINT1 | Port N | |
K1 | VD_VINT0 | ||
J2 | RSX_INT | ||
J1 | RSX_FLDO | ||
H2 | PN6 | ||
H1 | PN5 | ||
G2 | RSX_RESET | ||
G1 | RSX_SPI_CLK | RSX SPI Bus | |
F2 | RSX_SPI_DO | ||
F1 | RSX_SPI_DI | ||
E2 | RSX_SPI_CS |