Teensy++ 2.0: Difference between revisions

From PS3 Developer wiki
Jump to navigation Jump to search
Line 18: Line 18:
This model requires the following:
This model requires the following:


1x Dremel Tool
1x Dremel Tool<br>
1x Drill
1x Drill<br>
1x Roll of Double Sided Foam Tape
1x Roll of Double Sided Foam Tape<br>
1x 30AWG Kynar Wire or 26 AWG Kynar Wire.  (Few have reported 30AWG may be too small and has interference but does work if done well.)
1x 30AWG Kynar Wire or 26 AWG Kynar Wire.  (Few have reported 30AWG may be too small and has interference but does work if done well.)<br>
1x Torque 8 Screwdriver
1x Torque 8 Screwdriver<br>
1x Regular Phillips Head Screwdriver
1x Regular Phillips Head Screwdriver<br>
1x Solder (Can be leaded or no-lead)
1x Solder (Can be leaded or no-lead)<br>
1x Soldering Iron  (Radioshack 15-30 Watt Will Work.)
1x Soldering Iron  (Radioshack 15-30 Watt Will Work.)<br>
1x Pair Of Steady Hands  (Not Joking.  Tremor Fingers will not cut it. You are soldering 40+ points and all must be done very well.)
1x Pair Of Steady Hands  (Not Joking.  Tremor Fingers will not cut it. You are soldering 40+ points and all must be done very well.)<br>
1x Good Lighting  (Either very well lighted room, or a Lamp.  You need to be able to check your work.)
1x Good Lighting  (Either very well lighted room, or a Lamp.  You need to be able to check your work.)<br>
1x Magnifying Glass  (To check your soldering joints.)
1x Magnifying Glass  (To check your soldering joints.)<br>
1x Patience.
1x Patience.



Revision as of 10:12, 21 December 2011

Teensy 2.0 ++ Information

  • NORway (not working link, need working mirror)

Hardware Picture

Hardware Installations (Case Modifications by CECH Model)

First open the PS3. Follow youtube videos to learn how (Just search).

Once opened, look at the motherboard model printed there. Depending on which model you have follow the case modifications below to install teensy.

There are two methods to use a Teensy 2.0++ Flasher.

1.) Install while the PS3 is somewhat opened still with everything plugged in. (Be careful of shorts.)

2.) Internal Case Modifications. This is the best way to go as you can install the teensy inside of the PS3 for later use. This is the advantage of using a Teensy 2.0++ because it's just small enough to install inside the PS3 with a little case modification. Other flashers are generally too large to do this with the PS3 closed up. You will find there is just no room for it.

DYN-001

This model requires the following:

1x Dremel Tool
1x Drill
1x Roll of Double Sided Foam Tape
1x 30AWG Kynar Wire or 26 AWG Kynar Wire. (Few have reported 30AWG may be too small and has interference but does work if done well.)
1x Torque 8 Screwdriver
1x Regular Phillips Head Screwdriver
1x Solder (Can be leaded or no-lead)
1x Soldering Iron (Radioshack 15-30 Watt Will Work.)
1x Pair Of Steady Hands (Not Joking. Tremor Fingers will not cut it. You are soldering 40+ points and all must be done very well.)
1x Good Lighting (Either very well lighted room, or a Lamp. You need to be able to check your work.)
1x Magnifying Glass (To check your soldering joints.)
1x Patience.

DYN-001 Placement Area and first dremel
DYN-001 Wire direction and second dremel

JSD-001

..