Hard Drive

From PS2 Developer wiki
Jump to navigation Jump to search

Overview

Connecting a hard drive to the PS2 requires a Network Adaptor.

All official hard drives run special firmware, which implements some additional proprietary ATA-commands. Thus, official software requires official Sony PS2 hard drives. Homebrew software such as OPL does not require any of the proprietary commands, which means that a generic hard drive can be used as well for this purpose.

The PSX's internal hard drive implements the same proprietary ATA-commands, which are required for the console to boot. That's why the PSX's hard drive can only be replaced by another PSX's hard drive or one of the official Sony PS2 hard drives (which however only have a capacity of 40 GB, vs. 160 GB or 250 GB in the PSX). Note: DESR-x500 and DESR-x700 require the DVR-partition to boot. Thus, these consoles can NOT boot from a 40 GB PS2 drive!

For external hard drives (used with early SCPH-1X000 consoles), a special expandable vertical stand (SCPH-10220) was available separately, which allows the external hard drive to be placed vertically next to the vertical PS2 console.

Official PS2 software does not support 48-bit LBA, so drive size is generally limited to 128 GiB. In practice, this doesn't matter much, since the only drives supported by official software are the official drives sold by sony with their firmware customizations, which are all 40 GB in size.

Most homebrew software supports 48-bit LBA, so this isn't an issue here.

DVRP of the PSX will emulate the PS2's ATA interface for PS2-mode software (while PSX-mode software obviously natively uses the PSX's ATA interface, which supports 48-bit LBA, since the drives have a capacity of either 160 GB or 250 GB). For some reason, it also tries to emulate 48-bit LBA in PS2 mode and properly reports the full disk size, but fails any access beyond the 128 GiB limit in PS2 mode.

Models

SCPH-20400

  • Japan-only external hard drive for use with the PCMCIA type Network Adaptor (SCPH-10190) on SCPH-1X000 consoles.
  • Actually contains a drive with SCPH-20401 branding inside the external enclosure, the same drives that are used in the internal hard drive kit (see below for OEM model list)
  • Requires an external power supply (SCPH-10200)
  • Capacity: 40 GB

SCPH-20401

  • Internal hard drive for use with an expansion bay type Network Adaptor (SCPH-1025, SCPH-10281, SCPH-10350) on any console that has the expansion bay (SCPH-3XXXX or SCPH-5XXXX)
  • Comes with mounting brackets preinstalled (bracket type depends on height of the actual OEM drive)
  • Power is provided by the console through the Network Adaptor
  • Capacity: 40 GB

OEM drives used

This list might be incomplete; please add yours if it's not in the list.
For PSX hard drives, see PSX Hard drives

All official PS2 hard drives are 40 GB 3.5 inch IDE/P-ATA drives. They are all rebranded to Sony SCPH-20401, including those used in the SCPH-20400 external hard drive assembly for early PS2 consoles with PCMCIA slot. In the reported HDD ID however, the SCPH-20401-branded drives taken from an SCPH-20400 case report SCPH-20400 as part of their ID.

  • IBM "DeskStar" DTLA-305040 (standard height bracket)
  • Maxtor "DiamondMax D540X-4D" 4D040H2 (standard height bracket)
  • Maxtor "Fireball 3" 2F040L0 (low profile bracket)
  • Seagate "U Series 5" ST340823A (standard height bracket)
  • Seagate "Barracuda 5400.1" ST340015A (low profile bracket)

Sony custom ATA commands

The firmware of official PS2/PSX hard drives implements the following non-standard/vendor-specific ATA commands:

enum ATA_C_CODES {
	//left out standard commands
	ATA_C_SCE_SECURITY_CONTROL	= 0x8e,
};

enum ATA_SCE_SECURITY_CODES {
	ATA_SCE_IDENTIFY_DRIVE		= 0xec,

	ATA_SCE_SECURITY_SET_PASSWORD	= 0xf1,
	ATA_SCE_SECURITY_UNLOCK		= 0xf2,
	ATA_SCE_SECURITY_ERASE_PREPARE	= 0xf3,
	ATA_SCE_SECURITY_ERASE_UNIT	= 0xf4,
	ATA_SCE_SECURITY_FREEZE_LOCK	= 0xf5,

	ATA_SCE_SECURITY_READ_ID	= 0x20,
	ATA_SCE_SECURITY_WRITE_ID	= 0x30,
};

Source: ps2sdk/common/include/atahw.h

Security and authentication

Every original PS2 and PSX drive has a special sector containing security information which can be requested using the custom ATA_SCE_IDENTIFY_DRIVE command (0xEC).

Start End Length Description
0x00 0x1F 0x20 ASCII string: "Sony Computer Entertainment Inc."
0x20 0x2F 0x10 The drive's model number (or the console's model number in case of the PSX)
0x30 0x33 0x04 ASCII string containing the drive's capacity in GB. De facto "40" on all PS2 drives and "120" on all PSX drives, despite the PSX drives being larger than that.
0x34 0x3F 0x0C Probably padding. 0x00
0x40 0x43 0x04 Sony serial number of the drive.
0x44 0x45 0x02 Probably padding. 0x00
0x46 0x49 0x04 Unknown.
0x4A 0x4B 0x02 Probably padding. 0x00
0x4C 0x4F 0x04 Currently unknown. Always 0x01 0x03 0x11 0x01?
0x50 0x7F 0x30 Related to DNAS and encryption; details currently not (publicly) known.

Bundles including the hard drive

Japan

Hdd, external (SCPH-10210)

  • Japan-only bundle meant for use on SCPH-1X000 consoles which have a PCMCIA/PC-Card slot instead of the expansion bay. Contains:
    • PCMCIA Network Adaptor (SCPH-10190)
    • External hard drive 40 GB (SCPH-20400)
    • Power supply for the external hard drive (SCPH-10200)
    • Network Utility Disc
  • Released July 19, 2001

Hdd, expansion bay (SCPH-10260)

  • Japan-only bundle meant for use on any console that has the expansion bay (SCPH-3XXXX or SCPH-5XXXX). Contains:
    • Expansion bay Network Adaptor, old revision (SCPH-10250)
    • Internal hard drive 40 GB with mounting brackets (SCPH-20401)
    • Network Utility Disc
  • Released July 19, 2001

Linux kit, external (SCPH-10270 K)

  • Japan-only bundle meant for use on SCPH-1X000 consoles. Contains:
    • PCMCIA Network Adaptor (SCPH-10190)
    • External hard drive 40 GB (SCPH-20400), pre-formatted for Linux
    • Power supply for the external hard drive (SCPH-10200)
    • USB mouse (SCPH-10230)
    • USB keyboard, japanese (SCPH-10240)
    • VGA cable, Sync on Green, stereo cinch audio jacks (SCPH-10320)
    • PS2 Linux Beta Release 1 (1 Disc)
  • Released July 2001
  • PS2 Linux Release 1.0 software (2 Discs) became available at a later date for owners of the kit

PlayStation BB Unit, external (SCPH-10390)

  • Japan-only bundle meant for use on SCPH-1X000 consoles. Contains:
    • PCMCIA Network Adaptor (SCPH-10190)
    • External hard drive 40 GB (SCPH-20400)
    • Power supply for the external hard drive (SCPH-10200)
    • BB Navigator Disc
  • Released June 12, 2003

PlayStation BB Unit, expansion bay (SCPH-10400)

  • Japan-only bundle meant for use on any console that has the expansion bay (SCPH-3XXXX or SCPH-5XXXX). Contains:
    • Expansion bay Network Adaptor, newer revision (SCPH-10350)
    • Internal hard drive 40 GB with mounting brackets (SCPH-20401)
    • BB Navigator Disc
  • Released June 12, 2003

PlayStation 2 BB Pack (SCPH-50000 MB/NH)

  • Japan-only
    • All contents from SCPH-10400 (see above)
    • SCPH-50000 console in special "Midnight Blue" transparent case (similar to the limited SCPH-37000 consoles, but without the special cooler design)
  • Released November 13, 2003

US

Final Fantasy XI

  • US-only bundle. Contains:
    • Internal hard drive 40 GB with mounting brackets (SCPH-20401), pre-formatted and preloaded with software
    • HDD Utility Disc
    • Main game + manual
  • Does not include the Network Adaptor (required, had to be purchased separately)
  • The US PS2 release of Final Fantasy XI was only available in this bundle; no standalone release
  • In the US, the hard drive, too, was only available in this exact bundle (except as part of the Linux kit)
  • Released March 23, 2004

Linux kit (SCPH-97047)

  • Contains (incomplete, WIP):
    • Internal hard drive 40 GB with mounting brackets (SCPH-20401), pre-formatted for Linux
    • Network adapter, Ethernet-only version,
    • USB mouse (SCPH-10230)
    • USB keyboard, US (SCPH-10240 E)

Europe

Hdd (internal) + Network Adaptor kit (SCPH-10310 E)

  • Only available as part of the european release of the Linux kit or the University Development Kit

Linux kit

University Development Kit