MechaCon/UART commands: Difference between revisions

From PS2 Developer wiki
Jump to navigation Jump to search
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
== Overview ==
== Overview ==
These commands can be sent to [[MechaCon]] via it's UART interface. They exist for manufacturing and servicing purposes. For wiring up a serial terminal to the MechaCon UART interface, see [[Test points/MechaCon UART|MechaCon UART test points]].
These commands can be sent to [[MechaCon]] via it's UART interface. They exist for manufacturing and servicing purposes. For wiring up a serial terminal to the MechaCon UART interface, see [[Test points/MechaCon UART|MechaCon UART test points]].
To enable the UART interface, the console must be put in testmode by pulling the RMC test point to ground.
To enable the UART interface, the console must be put into testmode by pulling the RMC test point to ground.


'''Instead of working with raw MechaCon commands, it is recommended for users to use pre-made tools like [https://github.com/ps2homebrew/PMAP/tags PMAP]. The purpose of this page is to provide documentation for the further development of PS2 tools.'''
'''Instead of working with raw MechaCon commands, it is recommended for users to use pre-made tools like [https://github.com/ps2homebrew/PMAP/tags PMAP]. The purpose of this page is to provide documentation for the further development of PS2 tools.'''
Large differences exist between the SPC970-based MechaCon and the ARM-based "Dragon" MechaCon.


== Commands ==
== Commands ==
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"
* [[MechaCon/UART commands/SPC970|SPC970 commands]]
|- bgcolor="#cccccc"
* [[MechaCon/UART commands/Dragon|Dragon commands]]
! Command !! Description !! Parameters !! Return values !! Remarks
|-
| 0xc00 || MECHA_CMD_INIT_SHIMUKE || || ||
|-
| 0xc01 || MECHA_CMD_INIT_MECHACON || || ||
|-
| 0xc10 || MECHA_CMD_DISC_MODE_CD_8 || || ||
|-
| 0xc11 || MECHA_CMD_DISC_MODE_CD_12 || || ||
|-
| 0xc12 || MECHA_CMD_DISC_MODE_DVDSL_8 || || ||
|-
| 0xc13 || MECHA_CMD_DISC_MODE_DVDDL_8 || || ||
|-
| 0xc14 || MECHA_CMD_DISC_MODE_DVDSL_12 || || ||
|-
| 0xc15 || MECHA_CMD_DISC_MODE_DVDDL_12 || || ||
|-
| 0xc16 || MECHA_CMD_DISC_DETECT ||  ||  ||
|-
| 0xc20 || MECHA_CMD_LASER_DIODE ||  ||  ||
|-
| 0xc22 || MECHA_CMD_FOCUS_UPDOWN ||  ||  ||
|-
| 0xc23 || MECHA_CMD_FOCUS_AUTO_START ||  ||  ||
|-
| 0xc24 || MECHA_CMD_FOCUS_AUTO_STOP ||  ||  ||
|-
| 0xc25 || MECHA_CMD_FCS_SEARCH_CHECK ||  ||  ||
|-
| 0xc30 || MECHA_CMD_TRACKING ||  ||  ||
|-
| 0xc41 || MECHA_CMD_SLED_CTL_MICRO ||  ||  ||
|-
| 0xc42 || MECHA_CMD_SLED_CTL_BIPHS ||  ||  ||
|-
| 0xc43 || MECHA_CMD_SLED_CTL_POS ||  ||  ||
|-
| 0xc44 || MECHA_CMD_SLED_POS_HOME ||  ||  ||
|-
| 0xc45 || MECHA_CMD_SLED_IN_SW ||  ||  ||
|-
| 0xc50 || MECHA_CMD_SP_CTL ||  ||  ||
|-
| 0xc51 || MECHA_CMD_SP_CLV_S ||  ||  ||
|-
| 0xc52 || MECHA_CMD_SP_CLV_A ||  ||  ||
|-
| 0xc60 || MECHA_CMD_TRAY ||  ||  ||
|-
| 0xc61 || MECHA_CMD_TRAY_SW ||  ||  ||
|-
| 0xc8d || MECHA_CMD_CLEAR_CONF ||  ||  ||
|-
| 0xc8e || MECHA_CMD_UPLOAD_NEW ||  ||  || 00
|-
| 0xc93 || MECHA_CMD_UPLOAD_TO_RAM ||  ||  ||
|-
| 0xc97 || MECHA_CMD_DETECT_ADJ ||  ||  ||
|-
| 0xc99 || MECHA_CMD_WRITE_CHECKSUM ||  ||  ||
|-
| 0xc9a || MECHA_CMD_READ_CHECKSUM ||  ||  ||
|-
| 0xc9b || MECHA_CMD_SETUP_OSD ||  ||  || 00 = NTSC, 01 = PAL, presumed to be supported by DEX B and later.
|-
| 0xc9e || MECHA_CMD_SETUP_SANYO ||  ||  ||
|-
| 0xca1 || MECHA_CMD_AUTO_ADJ_ST_1 ||  ||  ||
|-
| 0xca2 || MECHA_CMD_AUTO_ADJ_ST_2 ||  ||  ||
|-
| 0xca3 || MECHA_CMD_AUTO_ADJ_ST_12 ||  ||  ||
|-
| 0xca4 || MECHA_CMD_AUTO_ADJ_ST_2MD ||  ||  || Performed during skew adjustment initialization.
|-
| 0xca5 || MECHA_CMD_AUTO_ADJ_FIX_GAIN ||  ||  ||
|-
| 0xca7 || MECHA_CMD_RFDC_LEVEL ||  ||  ||
|-
| 0xca8 || MECHA_CMD_TPP ||  ||  ||
|-
| 0xcaa || MECHA_CMD_MIRR_CHECK ||  ||  ||
|-
| 0xcab || MECHA_CMD_FE_OFFSET ||  ||  ||
|-
| 0xcb0 || MECHA_CMD_CD_PLAY_1 ||  ||  || 1x
|-
| 0xcb1 || MECHA_CMD_CD_PLAY_2 ||  ||  || 2x
|-
| 0xcb2 || MECHA_CMD_CD_PLAY_3 ||  ||  || 4x
|-
| 0xcb3 || MECHA_CMD_CD_PLAY_4 ||  ||  || 5-12x
|-
| 0xcb4 || MECHA_CMD_CD_STOP ||  ||  ||
|-
| 0xcb5 || MECHA_CMD_CD_PAUSE ||  ||  ||
|-
| 0xcb6 || MECHA_CMD_CD_TRACK_CTL ||  ||  ||
|-
| 0xcb8 || MECHA_CMD_CD_TRACK_LONG_CTL ||  ||  ||
|-
| 0xcb9 || MECHA_CMD_CD_PLAY_5 ||  ||  || 10-24x
|-
| 0xcc0 || MECHA_CMD_DVD_PLAY_1 ||  ||  || 1x
|-
| 0xcc1 || MECHA_CMD_DVD_PLAY_2 ||  ||  || 1.6x
|-
| 0xcc2 || MECHA_CMD_DVD_PLAY_3 ||  ||  || 1.6-4x
|-
| 0xcc3 || MECHA_CMD_DVD_STOP ||  ||  ||
|-
| 0xcc4 || MECHA_CMD_DVD_PAUSE ||  ||  ||
|-
| 0xcc5 || MECHA_CMD_DVD_TRACK_CTL ||  ||  ||
|-
| 0xcc7 || MECHA_CMD_DVD_TRACK_LONG_CTL ||  ||  ||
|-
| 0xcc8 || MECHA_CMD_FOCUS_JUMP ||  ||  ||
|-
| 0xcca || MECHA_CMD_ADJ_AUTO_TILT ||  ||  ||
|-
| 0xccb || MECHA_CMD_INIT_AUTO_TILT ||  ||  ||
|-
| 0xccd || MECHA_CMD_MOV_AUTO_TILT ||  ||  ||
|-
| 0xcd1 || MECHA_CMD_SET_DSP ||  ||  ||
|-
| 0xcd3 || MECHA_CMD_GAIN ||  ||  ||
|-
| 0xcde || MECHA_CMD_DSP_ERROR_RATE_CTL ||  ||  ||
|-
| 0xcdf || MECHA_CMD_DSP_ERROR_RATE ||  ||  ||
|-
| 0xce0 || MECHA_CMD_EEPROM_WRITE || aaaadddd ||  || ce0aaaadddd    a = address, d = data.
|-
| 0xce1 || MECHA_CMD_EEPROM_READ || aaaa ||  || ce1aaaa    a = address
|-
| 0xce4 || MECHA_CMD_RTC_READ ||  ||  ||
|-
| 0xce5 || MECHA_CMD_RTC_WRITE ||  ||  ||
|-
| 0xce6 || MECHA_CMD_ECR_READ ||  ||  ||
|-
| 0xce7 || MECHA_CMD_ECR_WRITE ||  ||  ||
|-
| 0xce8 || MECHA_CMD_CD_ERROR ||  ||  ||
|-
| 0xce9 || MECHA_CMD_JITTER ||  ||  ||
|-
| 0xcf2 || MECHA_CMD_FOCUS_JUMP_NEW ||  ||  ||
|-
| 0xcfa || MECHA_CMD_CFA ||  ||  ||
|-
| 0xcfc || MECHA_CMD_READ_MODEL_2 ||  ||  ||
|-
| 0xcfd || MECHA_CMD_READ_MODEL ||  ||  ||
|-
| 0xcfe || MECHA_CMD_EEPROM_ERASE ||  ||  ||
|-
 
|}

Latest revision as of 15:31, 27 April 2023

Overview[edit | edit source]

These commands can be sent to MechaCon via it's UART interface. They exist for manufacturing and servicing purposes. For wiring up a serial terminal to the MechaCon UART interface, see MechaCon UART test points. To enable the UART interface, the console must be put into testmode by pulling the RMC test point to ground.

Instead of working with raw MechaCon commands, it is recommended for users to use pre-made tools like PMAP. The purpose of this page is to provide documentation for the further development of PS2 tools.

Large differences exist between the SPC970-based MechaCon and the ARM-based "Dragon" MechaCon.

Commands[edit | edit source]

Retrieved from "http://www.psdevwiki.com/ps2/index.php?title=MechaCon/UART_commands&oldid=2033"