Editing Talk:Switch boards

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
== Pin 1 identification ==
All components whose pins needs to be marked in electronic equipment (because the component has several pins, like any chip/IC or connectors) always has a mark in pin 1... sometimes this mark is not visible because is "printed" under the component itself (so only visible before soldering the component to the board)... this seems to be the case in some of the connectors in PS3 power/eject boards, so the identification of pin 1 can be confusing


As example... HSW-001 board has a "copper point" marked close to the connector... but this point is the ground pin of the capacitor placed below (the blue text in the first photo is wrong because this point is not related with the connector). So there is no way to identify pin1 by looking at HSW-001 board... the solution is to look at the connector in the other side of the ribbon cable (in other words... in the main motherboard)
== PS3 2000 series Power Eject boards, enabling contour leds talk ==
<div style="float:right">[[File:Power Eject board PS3 2000 series (light rays schematic in contour leds).jpg|1000px|thumb|left|Power Eject board PS3 2000 series (light rays schematic in contour leds)]]<BR />[[File:Power Eject board HSW-001 (enabling contour leds).jpg|1000px|thumb|left|Power Eject board HSW-001 (enabling contour leds)]]</div>
This is a temporal section to discuss the simplest/easyer/safest/better way to make this mod, and the posible variations


<gallery>
The drawings at the right are a first sketch to discuss how to improve the drawings itself or the circuit, and are intented to replace the photos of this section in front page: http://www.ps3devwiki.com/wiki/Power_Eject_boards#Modding
File:Power Eject board HSW-001 (Connector pin 1 detail).jpg|The blue text is wrong because this point is not related with the connector but this is actually pin 1 if you look at the motherboard and trace it along the ribbon cable
File:Power Eject board HSW-001 (JSD-001) schematic.jpg|But by looking at this photo of the motherboard is visible another point that is actually the pin 1 mark of the connector
</gallery>


==Non retail Switch boards==
*Light rays bouncing photo (this goes first because is easy to discuss)
[[SW-13]], used in [[COOKIE-13]]
**I could not find a better one where the first bouncing surface is more visible, this first surface is the most important but also the curve for the next bounces, is good to cover this with a mirror sticker (by sticking it in the case, this way the glue layer is at the other side)... no photo of this sticker
<gallery>
**Is barelly visible the light ray starts in verticall, and after the first bounce is in horizontal... arrows didnt helped
File:COKIE-13-33.jpg|COOKIE-13 ([[CSW-001]] [[SW-13]]_B)
 
File:COKIE-13-32.jpg|COOKIE-13 ([[CSW-001]] [[SW-13]]_A)
*Circuit squematic photo
</gallery>
 
The cutted trace in pin1 is just because the board was designed to be controlled this way, even if is not in retail models is probable that exist a prototype with it (or is connected to an intermediary device), also is needed to be 100% sure the pin goes nowhere (is posible the trace goes to an internal layer of the motherboard not visible in the surface and emerge again in a syscon pin)
 
The cutted trace in pin 3 to disable the 4 white leds for power eject buttons backlight is just a paranoid meassure to controll the total current of the board (you are adding 4 leds, so other 4 "needs" to be disabled)
 
The transistor base pin goes in-line with the other unpopulated transistor base pin, both does the same function at the same time, each transistor is in chargue of 2 leds with a common capacitor (the transistor opens/closes the leds ground lines, and when the line is opened the zener diode works as an "voltage regulator" for the subcircuit avoiding "voltage peaks"). These transistors are "isolating" the subcircuit at his left
 
The unpopulated resistors values are dependant of the leds added, so no need to add the values to the drawing
 
 
*Bonus brainstorming
**If the pin1 line is really disabled, we can use it to carry other signals from the motherboard, like a temperature sensor, the PWM pulse of the fan, etc... add a small microcontroller in the power eject board with code to controll leds based in temperature (a PIC is a good candidate and there are 5v in the board) or even some kind of small display, etc...
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)