Editing Thermal

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
Relative: see also [[Cooling]], [[Thermal]], [[Syscon Thermal Configs]]
Relative: see also [[Cooling]], [[Thermal]], [[Syscon Thermal Config]]
<div style="float:right">[[File:CellBE-heatdistribution.jpg|200px|thumb|left|[[CELL BE]] heatdistribution (on die)]]</div>
<div style="float:right">[[File:CellBE-heatdistribution.jpg|200px|thumb|left|[[CELL BE]] heatdistribution (on die)]]</div>


== Motherboard Thermal Management ==
== Motherboard Thermal Management ==
All the thermal sensors of the PS3 motherboard are connected to [[Syscon Hardware|syscon]], the current temperatures are compared with the settings of a syscon [[SC EEPROM|EEPROM]] region named [[Syscon Thermal Configs|thermal config]] and based in the results of the comparison syscon sets a fan speed
All the thermal sensors of the PS3 motherboard are connected to [[Syscon Hardware|syscon]], the current temperatures are compared with the settings of a syscon [[SC EEPROM|EEPROM]] region named [[Syscon Thermal Config|thermal config]] and based in the results of the comparison syscon sets a fan speed


=== [[CELL BE]] Internal Powermanagement ===
=== [[CELL BE]] Internal Powermanagement ===
Line 40: Line 40:
{| class="wikitable" style="text-align:center; font-size:small;"
{| class="wikitable" style="text-align:center; font-size:small;"
|+ Temperature monitors models by motherboard model
|+ Temperature monitors models by motherboard model
! [[Motherboard_Revisions|Mother Board]] !! [[CELL BE|CELL]] !! [[RSX]] !! [[South Bridge|SB]] !! class="plainlinks" | [http://en.wikipedia.org/wiki/Emotion_Engine EEGS] !! BEVR !! GbE !! XDR !! Air intake !! [[Syscon Thermal Configs|Thermal Config]] [[Syscon_Thermal_Configs/structs|Format]] !! Notes
! [[Motherboard_Revisions|Mother Board]] !! [[CELL BE|CELL]] !! [[RSX]] !! [[South Bridge|SB]] !! class="plainlinks" | [http://en.wikipedia.org/wiki/Emotion_Engine EEGS] !! BEVR !! GbE !! XDR !! Air intake !! Others/Notes
|-
|-
! [[TMU-520]]
! [[TMU-520]]
| ADT7461 ? || ADT7461A ? || ADT75 || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || ADT75 || ADT75 || ADT75 || v0 ([[Mullion]] flash / pre-retail) ||
| ADT7467 || ADT7467 || ADT75 || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || ADT75 || ADT75 || ADT75 ||  
|-
! style="padding:0px" colspan="11" |
|-
|-
! [[COK-001]]
! [[COK-001]]
| ADT7461<small>'''(T1B)'''</small> || ADT7461A<small>'''(T1L)'''</small> || AD51 || {{cellcolors|lightgrey}} <abbr title="unpopulated">AD51</abbr> || {{cellcolors|lightgrey}} <abbr title="unpopulated">AD51</abbr> || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || rowspan="2" | v1 ([[Mullion]] 32KB / old) ||  
| AD51 || <abbr title="ADT7461A SMBus address 0x4D">T1L</abbr> || AD51 || AD51 || AD51 || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[COK-002]]
! [[COK-002]]
| ADT7461<small>'''(T1B)'''</small> || ADT7461A<small>'''(T1L)'''</small> || AD51 || {{cellcolors|lightgrey}} <abbr title="unpopulated">AD51</abbr> || {{cellcolors|lightgrey}} <abbr title="unpopulated">AD51</abbr> || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||
| AD51 || <abbr title="ADT7461A SMBus address 0x4D">T1L</abbr> || AD51 || {{cellcolors|#ff9999}} N/A || AD51 || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
! style="padding:0px" colspan="11" |
|-
|-
! [[SEM-001]]
! [[SEM-001]]
| ADT7461<small>'''(T1B)'''</small> || ADT7461A<small>'''(T1L)'''</small> || AD51 || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || rowspan="4" | v2 ([[Mullion]] 20KB / new) ||  
| AD51 || <abbr title="ADT7461A SMBus address 0x4D">T1L</abbr> || AD51 || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[DIA-001]]
! [[DIA-001]]
| ADT7461<small>'''(T1B)'''</small><br>or<br>TMP411A || ADT7461A<small>'''(T1L)'''</small><br>or<br>TMP411B || AD51 || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="ADT7461 SMBus address 0x4C">T1B</abbr> or <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="ADT7461A SMBus address 0x4D">T1L</abbr> or <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[DIA-002]]
! [[DIA-002]]
| ADT7461<small>'''(T1B)'''</small> || ADT7461A<small>'''(T1L)'''</small> || {{cellcolors|lightgrey}} <abbr title="unpopulated">AD51</abbr> || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || Speculation: either onsemi T1B/T1L or texas instruments 411A/411B
| <abbr title="ADT7461 SMBus address 0x4C">T1B</abbr> || <abbr title="ADT7461A SMBus address 0x4D">T1L</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || Speculation: either onsemi T1B/T1L or texas instruments 411A/411B
|-
|-
! [[DEB-001]]
! [[DEB-001]]
| ? || ? || {{cellcolors|lightgrey}} <abbr title="unpopulated">AD51</abbr> || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || Speculation: either onsemi T1B/T1L or texas instruments 411A/411B
| ? || ? || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || Speculation: either onsemi T1B/T1L or texas instruments 411A/411B
|-
|-
! style="padding:0px" colspan="11" |
! [[VER-001]]
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || Speculation: either onsemi T1B/T1L or texas instruments 411A/411B
|-
|-
! [[VER-001]]
! colspan="10" |  
| TMP411A || TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || rowspan="13" | v3 ([[Sherwood]]) || Speculation: either onsemi T1B/T1L or texas instruments 411A/411B
|-
|-
! [[DYN-001]]
! [[DYN-001]]
| ADT7461<small>'''(T1B)'''</small><br>or<br>TMP411A || ADT7461A<small>'''(T1L)'''</small><br>or<br>TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="ADT7461 SMBus address 0x4C">T1B</abbr> or <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="ADT7461A SMBus address 0x4D">T1L</abbr> or <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[SUR-001]]
! [[SUR-001]]
| TMP411A || TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[JTP-001]]
! [[JTP-001]]
| TMP411A || TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[JSD-001]]
! [[JSD-001]]
| TMP411A || TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[KTE-001]]
! [[KTE-001]]
| TMP411A || TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
! colspan="10" |  
|-
|-
! [[MSX-001]]
! [[MSX-001]]
| TMP411A || TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[MPX-001]]
! [[MPX-001]]
| TMP411A || TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[NPX-001]]
! [[NPX-001]]
| TMP411A || TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[PPX-001]]
! [[PPX-001]]
| ? || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| ? || ? || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[PQX-001]]
! [[PQX-001]]
| TMP411A || TMP411B || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[RTX-001]]
! [[RTX-001]]
| ? || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| ? || ? || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|-
|-
! [[REX-001]]
! [[REX-001]]
| TMP411A || TMP411B<br>or<br>201BI1309L || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
| <abbr title="Texas Instruments TMP411A SMBus address 0x4C">411A</abbr> || <abbr title="Texas Instruments TMP411B SMBus address 0x4D">411B</abbr> or 201BI1309L || ? || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A || {{cellcolors|#ff9999}} N/A ||  
|}
|}


Line 126: Line 124:
! Pin !! Signal !! Description
! Pin !! Signal !! Description
|-
|-
| 1 || VDD || from '''[[Regulators#OnSemi_NCP511SN33T1G_.283.3V_150_mA_CMOS_Low_Iq_Low-Dropout_Voltage_Regulator.29|+3.3V_THERMAL]]''' (with C1104 0.1μF B 10V 1005 to Ground as filter)
| 1 || VDD || from +3.3_Thermal (with C1104 0.1μF B 10V 1005 to Ground as filter)
|-
|-
| 2 || D+ || from [[CELL BE]] AU17 pad STI_THERMAL0 via R1106 100 Ohm and C1103 0.001{{micro}}F 50V
| 2 || D+ || from [[CELL BE]] AU17 pad STI_THERMAL0 via R1106 100 Ohm and C1103 0.001{{micro}}F 50V
Line 132: Line 130:
| 3 || D- || from [[CELL BE]] AT17 pad STI_THERMAL1 via R1107 100 Ohm and C1103 0.001{{micro}}F 50V
| 3 || D- || from [[CELL BE]] AT17 pad STI_THERMAL1 via R1107 100 Ohm and C1103 0.001{{micro}}F 50V
|-
|-
| 4 || /THERM || Not connected
| 4 || /THERM ||  
|-
|-
| 5 || GND || Ground
| 5 || GND || Ground
|-
|-
| 6 || /THERM2 || to /THRBE_SENS_ALRT (SYS_THR_ALRT since SEM-001)
| 6 || /THERM2 || to /THRBE_SENS_ALRT
|-
|-
| 7 || SDATA || from THR_I2C_SDA
| 7 || SDATA || from THR_I2C_SDA
Line 151: Line 149:
**pin 7 (THR_I2C_SDA) connected to syscon SWx-x series pin 24 by a 50ohm resistor
**pin 7 (THR_I2C_SDA) connected to syscon SWx-x series pin 24 by a 50ohm resistor
**pin 8 (THR_I2C_SCL) connected to syscon SWx-x series pin 25
**pin 8 (THR_I2C_SCL) connected to syscon SWx-x series pin 25
*It seems in the first PS3 models the signal SYS_THR_ALRT can be sent to syscon by both: CELL (using a pad named THERMAL_OVERLOAD connected to a transistor that drives a syscon pin to ground), and by the CELL temperature monitor (pin 6 of this chip). In later PS3 models (around PS3 slim) only CELL can do it
{{clear}}
{{clear}}


Line 168: Line 164:
! Pin !! Signal !! Description
! Pin !! Signal !! Description
|-
|-
| 1 || VCC || from '''[[Regulators#OnSemi_NCP511SN33T1G_.283.3V_150_mA_CMOS_Low_Iq_Low-Dropout_Voltage_Regulator.29|+3.3V_THERMAL]]''' (with C2108 0.1{{micro}}F B 10V 1005 to Ground as filter)
| 1 || VCC || from +3.3_Thermal (with C2108 0.1{{micro}}F B 10V 1005 to Ground as filter)
|-
|-
| 2 || D+ || from [[RSX]] AW12 pad RSX_TDP via R2101 100 Ohm and C2103 0.001{{micro}}F 50V
| 2 || D+ || from [[RSX]] AW12 pad RSX_TDP via R2101 100 Ohm and C2103 0.001{{micro}}F 50V
Line 189: Line 185:
**Texas Instrument Remote Junction Temperature Sensor TMP411'''B'''
**Texas Instrument Remote Junction Temperature Sensor TMP411'''B'''
**pin 1 (VDD) connected to pin 8 of voltage regulator 463A (3.3v standby named 3.3_EVER_A)
**pin 1 (VDD) connected to pin 8 of voltage regulator 463A (3.3v standby named 3.3_EVER_A)
**pin 4 connected to RSX input pad AV14 (RSX_THR_EVENT)
**pin 4 connected to RSX
**pin 6 not connected
**pin 6 not connected
**pin 7 (THR_I2C_SDA) connected to syscon SWx-x series pin 24 by a 50ohm resistor
**pin 7 (THR_I2C_SDA) connected to syscon SWx-x series pin 24 by a 50ohm resistor
Line 198: Line 194:
=== BE VR ===
=== BE VR ===
<div style="float:right">[[File:IC6108 - AD51(007Z-0REEL - CECHAxx -CECHBxx.png|200px|thumb|left|IC6108 - AD51/007Z-0REEL - [[CECHAxx]] [[CECHBxx]]]]<br>[[File:COK-001 VRM temperature monitor.png|200px|thumb|left|[[COK-001]] VRM temperature monitor]]</div>
<div style="float:right">[[File:IC6108 - AD51(007Z-0REEL - CECHAxx -CECHBxx.png|200px|thumb|left|IC6108 - AD51/007Z-0REEL - [[CECHAxx]] [[CECHBxx]]]]<br>[[File:COK-001 VRM temperature monitor.png|200px|thumb|left|[[COK-001]] VRM temperature monitor]]</div>
AD51/007Z-0REEL<br />
IC6108 on [[COK-001]] (unpopulated), located in between the NEC/TOKINS top side<br />
IC6108 on [[COK-001]] (unpopulated). Used for monitoring the VOLTAGE REGULATOR IC6303 [https://www.digikey.com/es/products/detail/rohm-semiconductor/BD3520FVM-TR/2673737 BD3520FVM-TR] and the MOSFET Q6310 [https://www.digikey.com/en/products/detail/vishay-siliconix/SUD40N02-08-E3/2623039 SUD40N02-08-E3] that generates '''+1.2V_YC_RC_VDDIO''' for <abbr title="And indirectly 6 pads of SB">CELL</abbr><br />
AD51/007Z-0REEL <br />
Configured as "local"
Configured as "local"<br />
Used for monitoring the VOLTAGE REGULATOR IC6303 [https://www.digikey.com/es/products/detail/rohm-semiconductor/BD3520FVM-TR/2673737 BD3520FVM-TR] and the MOSFET Q6310 [https://www.digikey.com/en/products/detail/vishay-siliconix/SUD40N02-08-E3/2623039 SUD40N02-08-E3] that generates '''+1.2V_YC_RC_VDDIO'''<!-- for RSX ? wtf --><br />


{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"  
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"  
Line 210: Line 207:
| 2 || SCL || from THR_I2C_SCL
| 2 || SCL || from THR_I2C_SCL
|-
|-
| 3 || OTI || Not connected
| 3 || OTI ||  
|-
|-
| 4 || GND || to Ground
| 4 || GND || Ground
|-
|-
| 5 || A2 || to Ground
| 5 || A2 || to Ground
Line 218: Line 215:
| 6 || A1 || to Ground
| 6 || A1 || to Ground
|-
|-
| 7 || A0 || to Ground
| 7 || A0 || to VDD
|-
|-
| 8 || VDD || from '''[[Regulators#OnSemi_NCP511SN33T1G_.283.3V_150_mA_CMOS_Low_Iq_Low-Dropout_Voltage_Regulator.29|+3.3V_THERMAL]]''' (with C6168 0.1{{micro}}F B 10V 1005 to ground as filter)
| 8 || VDD || from +3.3V_Thermal (with C6168 0.1{{micro}}F B 10V 1005 to ground as filter)
|-
|-
|}
|}
Line 226: Line 223:


=== SB ===
=== SB ===
<div style="float:right">[[File:IC3101 - 6-710-196-01 - AD51(007Z-0REEL (CXD2973GB monitor).png|200px|thumb|left|IC3101 - AD51/007Z-0REEL - [[CECHAxx]] [[CECHBxx]] [[CECHCxx]] [[CECHExx]]]]<br />[[File:IC3002 - AD51(007Z-0REEL - CECHGxx.png|200px|thumb|left|IC3002 - AD51/007Z-0REEL - [[CECHGxx]]]]<br>[[File:DIA-001 SB temperature monitor removed.png|200px|thumb|left|[[DIA-001]] SB temperature monitor removed (T5C)]]</div>
<div style="float:right">[[File:IC3101 - 6-710-196-01 - AD51(007Z-0REEL (CXD2973GB monitor).png|200px|thumb|left|IC3101 - AD51/007Z-0REEL - [[CECHAxx]] [[CECHBxx]] [[CECHCxx]] [[CECHExx]]]]<br />[[File:IC3002 - AD51(007Z-0REEL - CECHGxx.png|200px|thumb|left|IC3002 - AD51/007Z-0REEL - [[CECHGxx]]]]<br>[[File:COK-001 SB temperature monitor.png|200px|thumb|left|[[COK-001]] SB temperature monitor]]<br>[[File:SEM-001 SB temperature monitor.png|200px|thumb|left|[[SEM-001]] SB temperature monitor]]</div>


AD51/007Z-0REEL <br />
AD51/007Z-0REEL <br />
Line 241: Line 238:
| 2 || SCL || from THR_I2C_SCL
| 2 || SCL || from THR_I2C_SCL
|-
|-
| 3 || OTI || Not connected
| 3 || OTI ||  
|-
|-
| 4 || GND || to Ground
| 4 || GND || Ground
|-
|-
| 5 || A2 || to Ground
| 5 || A2 || to Ground
Line 249: Line 246:
| 6 || A1 || to Ground
| 6 || A1 || to Ground
|-
|-
| 7 || A0 || from '''[[Regulators#OnSemi_NCP511SN33T1G_.283.3V_150_mA_CMOS_Low_Iq_Low-Dropout_Voltage_Regulator.29|+3.3V_THERMAL]]''' (with C3155 0.1{{micro}}F B 10V 1005 to ground as filter)
| 7 || A0 || to VDD
|-
|-
| 8 || VDD || from '''[[Regulators#OnSemi_NCP511SN33T1G_.283.3V_150_mA_CMOS_Low_Iq_Low-Dropout_Voltage_Regulator.29|+3.3V_THERMAL]]''' (with C3155 0.1{{micro}}F B 10V 1005 to ground as filter)
| 8 || VDD || from +3.3V_Thermal (with C3155 0.1{{micro}}F B 10V 1005 to ground as filter)
|-
|-
|}
|}
<gallery>
File:COK-001 SB temperature monitor.png|[[COK-001]] [[South Bridge]] Temperature monitor
File:COK-002 SB temperature monitor.png|[[COK-002]] [[South Bridge]] Temperature monitor
File:SEM-001 SB temperature monitor.png|[[SEM-001]] [[South Bridge]] Temperature monitor
File:DIA-001 SB temperature monitor.png|[[DIA-001]] [[South Bridge]] Temperature monitor
File:DIA-002 SB temperature monitor.png|[[DIA-002]] [[South Bridge]] Temperature monitor
File:DEB-001 SB temperature monitor.png|[[DEB-001]] [[South Bridge]] Temperature monitor
</gallery>
{{clear}}
{{clear}}


Line 280: Line 268:
| 2 || SCL || from THR_I2C_SCL (via R7074 {{unk|50{{Ohm}}}})
| 2 || SCL || from THR_I2C_SCL (via R7074 {{unk|50{{Ohm}}}})
|-
|-
| 3 || OTI || Not connected
| 3 || OTI ||  
|-
|-
| 4 || GND || to Ground
| 4 || GND || Ground
|-
|-
| 5 || A2 || to Ground
| 5 || A2 || to Ground
|-
|-
| 6 || A1 || from '''[[Regulators#OnSemi_NCP511SN33T1G_.283.3V_150_mA_CMOS_Low_Iq_Low-Dropout_Voltage_Regulator.29|+3.3V_THERMAL]]''' (with C7286 0.1{{micro}}F B 10V 1005 to ground as filter)
| 6 || A1 || to Ground
|-
|-
| 7 || A0 || to Ground
| 7 || A0 || to VDD
|-
|-
| 8 || VDD || from '''[[Regulators#OnSemi_NCP511SN33T1G_.283.3V_150_mA_CMOS_Low_Iq_Low-Dropout_Voltage_Regulator.29|+3.3V_THERMAL]]''' (with C7286 0.1{{micro}}F B 10V 1005 to ground as filter)
| 8 || VDD || from +3.3V_Thermal (with C7286 0.1{{micro}}F B 10V 1005 to ground as filter)
|-
|-
|}
|}
Line 308: Line 296:
*The high/first byte can be converted to celsius degress by a direct decimal conversion, eg: 0xA=10ºC
*The high/first byte can be converted to celsius degress by a direct decimal conversion, eg: 0xA=10ºC
*The low/second byte can be converted from the hex value to a fraction of 1 celsius degre with the formula (decimal*100)/256. And the resulting value will be rounded following the tables below, eg 0x80 = (128*100)/256 = 50 (half a celsius degree, in other words 0.5ºC). This rounding depends of how is configured the "resolution" of the low/second byte and varyes per PS3 model
*The low/second byte can be converted from the hex value to a fraction of 1 celsius degre with the formula (decimal*100)/256. And the resulting value will be rounded following the tables below, eg 0x80 = (128*100)/256 = 50 (half a celsius degree, in other words 0.5ºC). This rounding depends of how is configured the "resolution" of the low/second byte and varyes per PS3 model
*Inside the [[Syscon Thermal Configs]] the temperature values for "TempU" and "TempD" are in little endian for [[Sherwood]], and big endian for [[Mullion]]. The other temperatures ("trp", "tshutdown" and "hyst") are in big endian for all syscon models
*Inside the [[Syscon Thermal Config]] the temperature values for "TempU" and "TempD" are in little endian for [[Sherwood]], and big endian for [[Mullion]]. The other temperatures ("trp", "tshutdown" and "hyst") are in big endian for all syscon models
*The temperature monitors of [[COK-001]] motherboard have the temperature data format (low/second byte) configured to use a '''0.0625°C resolution''', eg: the highest temperature that can be represented is 127.9375ºC with the bytes 0x7F 0xF0
*The temperature monitors of [[COK-001]] motherboard have the temperature data format (low/second byte) configured to use a '''0.0625°C resolution''', eg: the highest temperature that can be represented is 127.9375ºC with the bytes 0x7F 0xF0
*The temperature monitors of [[DYN-001]] motherboard have the temperature data format (low/second byte) configured to use a '''0.25°C resolution''', eg: the highest temperature that can be represented is 127.75ºC with the bytes 0x7F 0xC0
*The temperature monitors of [[DYN-001]] motherboard have the temperature data format (low/second byte) configured to use a '''0.25°C resolution''', eg: the highest temperature that can be represented is 127.75ºC with the bytes 0x7F 0xC0
*However, all the temperature values found in all the official [[Syscon Thermal Configs|thermal configs]] are adjusted to a '''0.5ºC resolution'''
*However, all the temperature values found in all the official [[Syscon Thermal Config|thermal configs]] are adjusted to a '''0.5ºC resolution'''


<div style="float:left; margin-right: 30px;">
<div style="float:left; margin-right: 30px;">
Line 424: Line 412:
</div>
</div>
</div><br style="clear: both;" />
</div><br style="clear: both;" />
=== I2C address ===
The temperature monitors of the manufacturer/model Analog Devices AD51 are configured as local (used for SB, EEGS, BEVR) and can be given a I2C address by the logic state of pins A0, A1, A2 (pulled up to volts, or pulled down to ground)
The circuit of the PS3 motherboards is designed to configure them automatically because everyone of them have the configuration pins "bridged" in a different way<br>
This means you can take the SB temperature monitor from a COK-001 motherboard and solder it in the position of the EEGS temperature monitor in the same motherboard, or in a different motherboard, just because you are soldering in a different position (so the pins A0, A1 and A2 are bridged in a different way... and as a consequence is given a different I2C address)<br>
For modding (incase the temperature monitor is going to be "floating" with wires, not directly soldered in the motherboard) it means you can choose the "I2C address" for it
Lets say... in a COK-001 or COK-002 motherboards you can use 4 wires to place a temperature monitor inside the PSU and give it the I2C address of "BEVR" by connecting pins 4,5,6,7 together, it should work because the syscon firmware (and the thermal config format) seems to support it, the only weird thing is it will be reported with the name BEVR because you are giving it the I2C address of BEVR
<div>
<div style="float:left">
{| class="wikitable"
! rowspan="2" | Monitored !! colspan="3" | AD51 pin config !! rowspan="2" | bits !! rowspan="2" | decimal
|-
! A0 !! A1 !! A2
|-
| ? || {{cellcolors|#f00}} VDD || {{cellcolors|#f00}} VDD || {{cellcolors|#f00}} VDD || 000 || 0
|-
| ? || {{cellcolors|#f00}} VDD || {{cellcolors|#f00}} VDD || {{cellcolors|#000|#fff}} GND || 001 || 1
|-
| ? || {{cellcolors|#f00}} VDD || {{cellcolors|#000|#fff}} GND || {{cellcolors|#f00}} VDD || 010 || 2
|-
| SB || {{cellcolors|#f00}} VDD || {{cellcolors|#000|#fff}} GND || {{cellcolors|#000|#fff}} GND || 011 || 3
|-
| ? || {{cellcolors|#000|#fff}} GND || {{cellcolors|#f00}} VDD || {{cellcolors|#f00}} VDD || 100 || 4
|-
| EEGS || {{cellcolors|#000|#fff}} GND || {{cellcolors|#f00}} VDD || {{cellcolors|#000|#fff}} GND || 101 || 5
|-
| ? || {{cellcolors|#000|#fff}} GND || {{cellcolors|#000|#fff}} GND || {{cellcolors|#f00}} VDD || 110 || 6
|-
| BEVR || {{cellcolors|#000|#fff}} GND || {{cellcolors|#000|#fff}} GND || {{cellcolors|#000|#fff}} GND || 111 || 7
|}
</div>
<div style="float:left">
[[File:IC3101 - 6-710-196-01 - AD51(007Z-0REEL (CXD2973GB monitor).png|x175px|thumb|left|SB <span style="background:#f00">&nbsp;VDD&nbsp;</span> <span style="background:#000; color:#fff">&nbsp;GND&nbsp;</span> <span style="background:#000; color:#fff">&nbsp;GND&nbsp;</span>]]
</div>
<div style="float:left">
[[File:IC7005 - AD51(007Z-0REEL - CECHAxx -CECHBxx.png|x175px|thumb|left|EEGS <span style="background:#000; color:#fff">&nbsp;GND&nbsp;</span> <span style="background:#f00">&nbsp;VDD&nbsp;</span> <span style="background:#000; color:#fff">&nbsp;GND&nbsp;</span>]]
</div>
<div style="float:left">
[[File:IC6108 - AD51(007Z-0REEL - CECHAxx -CECHBxx.png|x175px|thumb|left|BEVR <span style="background:#000; color:#fff">&nbsp;GND&nbsp;</span> <span style="background:#000; color:#fff">&nbsp;GND&nbsp;</span> <span style="background:#000; color:#fff">&nbsp;GND&nbsp;</span>]]
</div>
</div>{{clear}}


== Readout of Thermal and Fan data using Software ==
== Readout of Thermal and Fan data using Software ==
Line 572: Line 517:
<div style="float:right">[[File:Control fan utility 1.8.1.jpg|200px|thumb|left|Control fan utility]]</div>
<div style="float:right">[[File:Control fan utility 1.8.1.jpg|200px|thumb|left|Control fan utility]]</div>


* https://web.archive.org/web/*/http://ps3devwiki.com/files/devtools/PS3_Temp/  [http://www.filecrop.com/81195444/index.html mirror] [http://www.filecrop.com/81219150/index.html mirror]
* http://www.ps3devwiki.com/files/devtools/PS3_Temp/  [http://www.filecrop.com/81195444/index.html mirror] [http://www.filecrop.com/81219150/index.html mirror]


* [http://mods.elotrolado.net/~hermes/ps3/control_fan_utility_v0.3.rar control_fan_utility_v0.3.rar] (including source) [http://www.mirrorcreator.com/files/KVLXQPJW/control_fan_utility_v0.3.rar_links mirror] for 4.31 and 4.40 // [http://www.elotrolado.net/hilo_utilidad-control-fan-utility-v0-3-cfw-4-31-y-4-40-cex_1893851 original thread]
* [http://mods.elotrolado.net/~hermes/ps3/control_fan_utility_v0.3.rar control_fan_utility_v0.3.rar] (including source) [http://www.mirrorcreator.com/files/KVLXQPJW/control_fan_utility_v0.3.rar_links mirror] for 4.31 and 4.40 // [http://www.elotrolado.net/hilo_utilidad-control-fan-utility-v0-3-cfw-4-31-y-4-40-cex_1893851 original thread]
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)