Search results
Jump to navigation
Jump to search
Create the page "Resistor" on this wiki! See also the search results found.
- ...i.com/ps3/index.php?search=resistor&fulltext=Search&title=Special%3ASearch Resistor] || ...3/index.php?search=resistor+network&fulltext=Search&title=Special%3ASearch Resistor Network] ||3 KB (406 words) - 13:57, 22 November 2021
- ...om/toslink_receiver_files/Toslink_TX_dra.jpg see pinout]) goes to a 34 ohm resistor and from there to pin 7 of the tiny component in the photo labeled '''P3 121 KB (171 words) - 08:43, 20 July 2017
- ...ulti_Out_pinout_-_CN2401_12P|connector]] pin 4 (Cb/Pb/Blue) through 750ohm resistor ...V_Multi_Out_pinout_-_CN2401_12P|connector]] pin 1 (Y/Green) through 750ohm resistor15 KB (1,981 words) - 19:11, 21 March 2023
- ...ulti_Out_pinout_-_CN2401_12P|connector]] pin 4 (Cb/Pb/Blue) through 750ohm resistor ? ...V_Multi_Out_pinout_-_CN2401_12P|connector]] pin 1 (Y/Green) through 750ohm resistor ?11 KB (1,527 words) - 07:52, 19 October 2022
- *Resistor (220 Ohms)1 KB (162 words) - 22:47, 20 March 2022
- ...S high and applying 5 TCK pulses, or by pulling this pin low by a 4.7 kohm resistor. | 33 || RSET || I || Constant voltage reference. External 4.99 kohm 1% resistor connection to VSS required for each pin.9 KB (1,356 words) - 15:10, 5 February 2014
- ...dby line present in the switch board at all times). All LED's have its own resistor with a different value to control the current (thus light intensity) and on ...the red light almost not visible, so is a good idea to remove/replace the resistor or to remove the red LED, removing LEDs can be convenient because are diffe13 KB (2,279 words) - 03:57, 20 July 2017
- '''note:''' pin34 4.7K (472) resistor present (R6) - might need removing (to solve corruption errors, when applic5 KB (809 words) - 14:25, 2 November 2021
- ..., are connected to each other with a <abbr title="R1024 in SEM-001">0 ohms resistor</abbr> located in between CELL border and his [[Thermal#Temperature_Monitor ..., are connected to each other with a <abbr title="R1024 in SEM-001">0 ohms resistor</abbr> located in between CELL border and his [[Thermal#Temperature_Monitor21 KB (2,729 words) - 06:05, 1 July 2023
- | 22 || RREF || Reference resistor6 KB (796 words) - 05:09, 9 June 2015
- ...components involved seems to be the same in the same configuration... the resistor values and the control signal could vary by board though">very characterist ...current to the battery. This feature revives deeply discharged cells. The resistor connected between the '''ISET1''' and VSS determines the precharge rate. Th107 KB (16,341 words) - 10:02, 17 January 2024
- **All LED's have its own resistor with a different value to control the current (thus light intensity) and on13 KB (1,858 words) - 19:27, 5 December 2021
- ...01 has 3 points, 1 of them goes to the solder point, one goes to the tiny resistor above it labeled 153 <jordosaxman> yeah it looks like RV301 hits a resistor and then goes to pin 3 of IC30318 KB (2,723 words) - 06:37, 16 February 2024
- ...} || Connected to [[South Bridge]] [[CXD2973GB]] pad AP29 through a 22 ohm resistor ...br>Connected to [[South Bridge]] [[CXD2973GB]] pad AP28 through a 49.9 ohm resistor34 KB (4,383 words) - 13:03, 20 October 2022
- | 20 || Dummy || connected internally via 51 +/- 0.5% resistor to ground13 KB (1,761 words) - 13:14, 11 March 2024
- | 1 || PC Position || GND || A resistor is placed, by hand, between this pin and GND after the board is manufacture | 4 || DG Position|| GND || A resistor is placed, by hand, between this pin and GND after the board is manufacture21 KB (2,610 words) - 07:00, 17 April 2023
- **pin 7 (THR_I2C_SDA) connected to syscon SWx-x series pin 24 by a 50ohm resistor **pin 7 (THR_I2C_SDA) connected to syscon SWx-x series pin 24 by a 50ohm resistor55 KB (7,617 words) - 07:11, 17 April 2023
- === Resistor codes ===58 KB (8,246 words) - 06:18, 1 July 2023
- ...> TIM1_CH4 || {{no}} || USBDM || || || TP26 || || || Connected through 2.1Ωresistor ...> TIM1_ETR || {{no}} || USBDP || || || TP27 || || || Connected through 2.1Ωresistor33 KB (4,555 words) - 02:22, 7 May 2023
- To disable the led is posible to desolder it, or desolder its resistor, but technically the best way is by cutting its trace because we dont want42 KB (6,628 words) - 17:16, 16 September 2021