Search results

Create the page "Resistor" on this wiki! See also the search results found.

• Template:Syscon pinout BGA 200 pads
  ...R || MC_RESERVED2 || ? || Not connected to BluRay Drive because a missing resistor (R4080). BD_LED ...SET || ? || SS2_RESET (StarShip2 related), not connected because a missing resistor (R4135) ?
  50 KB (6,366 words) - 03:43, 16 November 2022
• Talk:Hardware flashing
  ...01 || {{Yes}} || {{No}} || <small>''example'' : Tried 128/128 and 4K/4096, resistor and A/B trick, always freezes on first sector</small> ...00_111002_2 (by Ago). Pullup 10Kohms btw R8 closed and rdy, and a 100Kohms resistor btw rdy_progskeet and rdy_nor. Rogero_CFW_V2 works fine on the ps3.</small>
  45 KB (6,787 words) - 19:36, 31 January 2022
• GL819
  | 22 || RREF || Reference resistor
  6 KB (796 words) - 05:09, 9 June 2015
• DualShock 3
  ...components involved seems to be the same in the same configuration... the resistor values and the control signal could vary by board though">very characterist ...current to the battery. This feature revives deeply discharged cells. The resistor connected between the '''ISET1''' and VSS determines the precharge rate. Th
  107 KB (16,356 words) - 17:00, 14 May 2024
• Switch boards
  **All LED's have its own resistor with a different value to control the current (thus light intensity) and on
  13 KB (1,858 words) - 19:27, 5 December 2021
• Power Supply
  ...01 has 3 points, 1 of them goes to the solder point, one goes to the tiny resistor above it labeled 153 <jordosaxman> yeah it looks like RV301 hits a resistor and then goes to pin 3 of IC303
  18 KB (2,723 words) - 06:37, 16 February 2024
• CXD9208GP
  ...} || Connected to [[South Bridge]] [[CXD2973GB]] pad AP29 through a 22 ohm resistor ...br>Connected to [[South Bridge]] [[CXD2973GB]] pad AP28 through a 49.9 ohm resistor
  34 KB (4,383 words) - 13:03, 20 October 2022
• Connectors
  | 20 || Dummy || connected internally via 51 +/- 0.5% resistor to ground
  13 KB (1,761 words) - 13:14, 11 March 2024
• PS3Cobra Payload Reverse Engineering
  | 1 || PC Position || GND || A resistor is placed, by hand, between this pin and GND after the board is manufacture | 4 || DG Position|| GND || A resistor is placed, by hand, between this pin and GND after the board is manufacture
  21 KB (2,610 words) - 07:00, 17 April 2023
• Talk:E3
  ...ons#KTE-001|KTE-001]] the SMD filter condensator(s) on VCC line and pullup resistor(s) on RY/BY line are not uncomfortably in the way demanding clip-remodellin
  14 KB (2,272 words) - 06:10, 5 May 2023
• Template:CELL pad layout 90nm
  ...-sort-value="0A11" | A11 || Y0_DQ0_RLOAD || BE_Y0_DQ0_RLOAD || {{pini}} || Resistor 49.9 ohms to +1.2V_YC_RC_VDDIO | data-sort-value="0A35" | A35 || RC_SCAN_CLK2 || || {{pin}} || Resistor 470K ohms (R1001) to GND
  351 KB (42,654 words) - 05:34, 16 November 2022
• Thermal
  **pin 7 (THR_I2C_SDA) connected to syscon SWx-x series pin 24 by a 50ohm resistor **pin 7 (THR_I2C_SDA) connected to syscon SWx-x series pin 24 by a 50ohm resistor
  55 KB (7,617 words) - 07:11, 17 April 2023
• Hardware flashing
  === Resistor codes ===
  58 KB (8,246 words) - 06:18, 1 July 2023
• Template:RSX pad layout 41x41
  ...n to reset he RSX "CG". But since PS3 slim this pad is "nerfed" with a 10k resistor to ground
  44 KB (5,008 words) - 17:08, 30 September 2022
• Move Motion Controller
  ...> TIM1_CH4 || {{no}} || USBDM || || || TP26 || || || Connected through 2.1Ωresistor ...> TIM1_ETR || {{no}} || USBDP || || || TP27 || || || Connected through 2.1Ωresistor
  33 KB (4,555 words) - 02:22, 7 May 2023
• Teensy++ 2.0
  To disable the led is posible to desolder it, or desolder its resistor, but technically the best way is by cutting its trace because we dont want
  42 KB (6,628 words) - 17:16, 16 September 2021
• File talk:Ps3spi.jpg
  ...and the card readers. You can see I have soldered a wire to the side of a resistor. This is the connection to the PS3 RAM control line that you need to solder
  40 KB (7,166 words) - 12:58, 11 November 2011
• Template:CELL pad layout 65nm
  ...([[Template:Syscon_pinout_LQFP_128_pins|LQFP 128 pins layout]]) through 47 resistor
  73 KB (6,284 words) - 05:37, 16 November 2022
• Syscon Error Codes
  ...as reading 140 ohms and not reading as a capacitor, so it was working as a resistor causing extra load in the fuse.
  59 KB (9,322 words) - 08:10, 10 May 2024