Search results

Jump to navigation Jump to search

Create the page "LED" on this wiki! See also the search results found.

Page title matches

Page text matches

  • File:Remarry error.jpg
    [[Category:Software]]Error during remarry and flashing green LED (non done)
    (909 × 631 (156 KB)) - 02:51, 25 April 2012
  • Template:KSW-001 pinout
    ...|| Red led || Connects to right-top corner pin (red gnd) of dual red/green LED over power switch, ...reen led || Connects to top right corner pin (green gnd) of dual red/green LED over power switch,
    1 KB (162 words) - 18:27, 5 December 2021
  • File:Eclipse-inserted-in-FAT-PS3-green-led-lit.png
    [[Category:Software]]Eclipse inserted in FAT PS3 - green led lit
    (600 × 239 (263 KB)) - 23:06, 6 September 2011
  • File:E3-Clip withot clamp gives bad dumps and errors led.JPG
    ...3-Clip without a clamp on Spansion NOR, gives allways bad dumps and errors led
    100 bytes (17 words) - 00:29, 22 March 2012
  • Template:DSW-001 pinout
    ...en led || Connects to bottom-left corner pin (green gnd) of dual red/green LED over power switch. ...|| Red led || Connects to top-left corner pin (red gnd) of dual red/green LED over power switch.
    2 KB (302 words) - 18:23, 5 December 2021
  • Template:HSW-001 pinout
    ...imitor resistors of 3K {{ohm}} (red led at left-top) and 820 {{ohm}} (blue led at left-bottom)<br>The circuit has unpopulated pads to add another transist ...ed - || Connects to left-bottom corner pin (green gnd) of ''dual red/green LED'' located next to the power switch, with a currentlimitor resistor of 1K {{
    3 KB (386 words) - 18:25, 5 December 2021
  • BL2-001
    ...the load/eject mechanical parts at top of the drive. SYSCON feeds this IR-LED through [[Template:Syscon_pinout_BGA_200_pads|mullion Pin M16]] (DISC_PHOT_ *IR LED (CL-200IR-X-TU)
    1 KB (162 words) - 22:47, 20 March 2022
  • File:E3-Clip with clamp to solve bad dumps.jpg
    ...well, now the Dump/Backup is successfull done(now no longer Error Blinking Led or bad dump content)
    (2,554 × 1,916 (1.46 MB)) - 03:47, 25 April 2012
  • Template:CSW-001 pinout
    ...POW_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad M7 || Green led || ...| STBY_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad N7 || Red led ||
    2 KB (225 words) - 05:56, 18 October 2022
  • User:Acab
    ...older those point but i can't get the e3 to dump the nor always the second led lights up is there any problem ???
    189 bytes (36 words) - 23:15, 23 March 2019
  • Talk:Remarry Bluray Drive
    # Controls what led does in case of (-OK-) on standard RSSI # LED ID
    7 KB (678 words) - 01:43, 10 February 2014
  • KSW-001
    ...t led, and 10th gnd pin on a 300X model full power eject and red and green led functions, A KSW-001 Will not work on a 200X model (dsw-001 slot) not teste
    1 KB (182 words) - 03:40, 20 July 2017
  • Template:Toshiba T6UN6EFG Pinout
    ...TBY || || 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, {{padps}}, and LED's ...TBY || || 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, {{padps}}, and LED's
    11 KB (1,476 words) - 13:17, 16 February 2019
  • DSW-001
    ...t led, and 10th gnd pin on a 300X model full power eject and red and green led, A KSW-001 Will not work on a 200X model (dsw-001 slot).
    2 KB (264 words) - 03:56, 20 July 2017
  • CECH-21xx
    ...w Light of Death" sequence was changed with this revision, where the power LED no longer turns yellow, although the rest of the sequence is the same. ...button three times, then power button twice. If done correctly, the power LED should now blink yellow once (to indicate the mode has been activated) then
    2 KB (363 words) - 13:26, 11 March 2024
  • PSGroove
    *BOARD = USER (need to manually attribute LED pins in Board/LEDs.h) ...ould light up. After about 5 seconds, the second LED will light up (or the LED will just go off, if you only have one). This means the exploit worked! You
    4 KB (663 words) - 23:33, 14 July 2017
  • User:Ps3hen
    ...which eventually led to the 4.00 Hybrid Firmware fad. Then my XMB research led me to become a developer for the XMB Manager Plus ([http://www.ps3crunch.ne
    2 KB (337 words) - 09:28, 19 November 2012
  • Talk:Teensy++ 2.0
    ...ins are input pins driven by southbridge.. not enough current to drive the led **Solution - Remove the led, alternativelly cut the LED trace, or disconnect D6 wire
    5 KB (793 words) - 00:31, 14 August 2017
  • HSW-001
    ...to the 5 volts standby line present in the switch board at all times). All LED's have its own resistor with a different value to control the current (thus *Contour LED's
    13 KB (2,279 words) - 03:57, 20 July 2017
  • CSW-001
    *Eject LED should be connected to BD controller [[CXD5063AGG-1]]
    874 bytes (121 words) - 01:18, 16 October 2020
View (previous 20 | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "http://www.psdevwiki.com/ps3/Special:Search"