Editing DualShock 3

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 318: Line 318:


=== Ribbon Circuit Boards ===
=== Ribbon Circuit Boards ===
For any arcade stick builders soldering to the vias on the PCB board (in the models where there are no testpoints availables) isn't exactly the easiest thing to do, using the copper contacts for the ribbon board is really the best option. In some board models (VX3, VX4, VX5, VX6, VX8) the copper contacts are covered by a black carbon material that needs to be removed if these spots are to be used to solder in them, this can be done with an X-acto knife or some fine sandpaper, just be careful and when you get to the shiny copper, STOP, you're done. Tin it up with some solder and there are your spots to use. Try and use a 30awg wire, or 28awg at the largest, and make sure to secure the wiring with some hot glue after you make the connection, but don't glue over the solder joint you just made, secure the wire to the board back from the solder joint, in case you ever have to get to it again for any reason.
For any arcade stick builders soldering to the vias on the PCB board (in the models where there are no testpoint availables) isn't exactly the easiest thing to do, using the contacts for the ribbon board is really the best option. The black carbon material needs to be removed if these spots are to be used, and this can be done with an X-acto knife or some fine sandpaper, just be careful and when you get to the shiny copper, STOP, you're done. Tin it up with some solder and there are your spots to use. Try and use a 30awg wire, or 28awg at the largest, and make sure to secure the wiring with some hot glue after you make the connection, but don't glue over the solder joint you just made, secure the wire to the board back from the solder joint, in case you ever have to get to it again for any reason.


The pull-up 7.5k Resistors ("printed" on the ribbon circuit boards) also need to be put back in the circuit as they're built into the ribbon board and when it's removed they're not, and the controller will act up on you if these are not in the circuit. There needs to be 2 of these pull-up resistors installed, one goes from V_STBY to COM1, the other goes from V_STBY to COM2. If you don't have any 7.5k resistors you can use anything from 6.8k to 10k really, but they do need to be installed since the ribbon board is removed when building an arcade stick, all of the PS3 controllers are setup this way and need those pull-up resistors if the ribbon board is removed
The pull-up 7.5k Resistors ("printed" on the ribbon circuit boards) also need to be put back in the circuit as they're built into the ribbon board and when it's removed they're not, and the controller will act up on you if these are not in the circuit. There needs to be 2 of these pull-up resistors installed, one goes from V_STBY to COM1, the other goes from V_STBY to COM2. If you don't have any 7.5k resistors you can use anything from 6.8k to 10k really, but they do need to be installed since the ribbon board is removed when building an arcade stick, all of the PS3 controllers are setup this way and need those pull-up resistors if the ribbon board is removed
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)