Editing Progskeet 1.21

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
== Support ==
[[Category:Hardware]][[Category:Software]]
{{Progskeet-support}}
= Progskeet Support =
[http://www.progskeet.com/mibbit.php Live Support]


== Anouncement ==
== Anouncement ==
Line 17: Line 18:
'''Note:''' It still has the Actel ProASIC3 A3P125 so they are not solving the 1.2 issue with the bitstream not fitting in the Actel (a problem of the 1.2 that still has not been fixed, even though the cause is obvious a design/implementation flaw).
'''Note:''' It still has the Actel ProASIC3 A3P125 so they are not solving the 1.2 issue with the bitstream not fitting in the Actel (a problem of the 1.2 that still has not been fixed, even though the cause is obvious a design/implementation flaw).


== Overview ==
=== Bitstreams ===
[JTAG] <-JTAG 15pin-> J2 [Progskeet 1.21] <-SPI/USB/switchlines 50pin-> J3 [SlaveBoard] <-SPI-> [AdaptorBoard] <-Flashbus-> [QuickSolderBoard]
for anyone who has v1.2/v1.21: [https://dl.dropbox.com/u/52587949/ProgSkeet_12_130330_1909.dat ProgSkeet_12_130330_1909.dat] [http://www.sendspace.com/file/ua6u2o] makes it work like a 1.1


===J2===
<uf6667> https://dl.dropbox.com/u/52587949/ProgSkeet_12_130401_2010.dat
JTAG, 15 pins, pinout (bottom 2): [[:File:Injectus-jtag-bottompads.png]]
<uf6667> I made this yesterday Mancer
<uf6667> I introduced a timeout for the "rdy" pin
<uf6667> so that in case rdy never goes high
<uf6667> it will continue anyway


===J3===
Slaveboard/Adaptorboard connector, 50 pins


===JTAG Pinout===
[http://forum.dayton360mods.com/downloads.php?do=file&id=21 ProgSkeet_12_130402_1730.dat]
<gallery>
* Added metastability to the DQ ports to filter out noise and glitches
File:Progkeet 1.2 - JTAG.jpg|Progskeet JTAG pinout - http://oi47.tinypic.com/s5d8g1.jpg
ProgSkeet_12_130401_2010.dat
</gallery>
* Reduced timeout from 1.3ms down to 320ns per word
 
[http://forum.dayton360mods.com/downloads.php?do=file&id=20 ProgSkeet_12_130401_1824.dat]
To flash FPGA without flatcable (normally used with Infectus) but soldered, this is the JTAG pinout
* Added timeout for reads/writes (1ms), no more blocking
 
* Fixed bug where it would read gpio from data pins rather than from gpio pins
TCK TDO TRST GND<br />
[http://forum.dayton360mods.com/downloads.php?do=file&id=19 ProgSkeet_12_130330_1909.dat]
&nbsp;&nbsp;TDI TMS VJTAG VCC
* Increased metastability of USB (should no longer disconnect)
 
* Restored Samsung Q compatibility that was caused by dualboot pin allocation
== Winskeet ==
{{Winskeet 1.2/1.21}}
 
== Bitstreams ==
{{Bitstreams_1.2/1.21}}
 
== Injectus and Updating Bitstreams ==
{{Updating Bitstreams_1.2/1.21}}
 
== Quick Solder Boards (QSB) ==
{{QSB_1.2/1.21}}
 
 
{{Hardware Flashers}}<noinclude>[[Category:Main]]</noinclude>
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)

Templates used on this page:

Retrieved from "http://www.psdevwiki.com/ps3/Progskeet_1.21"