Syscon Hardware: Difference between revisions
m (→Packets Logs) |
|||
Line 168: | Line 168: | ||
| 0x01 || '''bringup''' || <pre> (END) </pre> | | 0x01 || '''bringup''' || <pre> (END) </pre> | ||
|- | |- | ||
| 0x02 || '''shutdown''' || | | 0x02 || '''shutdown''' || <pre> Do nothing. (PowerOff State)\n (END) </pre> | ||
|- | |- | ||
| 0x03 || '''firmud''' || <pre> Erase User Program Area Start...\n (END) </pre> | | 0x03 || '''firmud''' || <pre> Erase User Program Area Start...\n (END) </pre> |
Revision as of 16:18, 15 April 2017
Syscon is the main power controller chip. It is responsible for powering up the various power systems and for configuring and initialising the CELL BE, RSX and South Bridge. It communicates with these devices via seperate SPI busses. There is external access by JTAG (disabled from factory on retail models), an EEPROM programming interface and Serial (UART). The Syscon is a SoC and consists of an ARM7TDMI (ARMv4) CPU, a 256KB EEPROM and 16KB RAM.
Serialnumbers @ SKU
Retail
Model | Type | Board | Syscon part no. |
Syscon Soft ID |
Notes |
---|---|---|---|---|---|
CECHAxx CECHBxx |
0x01 0x02 |
COK-001 | CXR713120-201GB | 0B8E | |
CECHCxx CECHExx |
0x03 0x04 |
COK-002 or COK-002W |
CXR713120-201GB or CXR713120-202GB |
0C16 | |
CECHGxx | 0x05 | SEM-001 | CXR713120-201GB or CXR713120-202GB or CXR713120-203GB |
0D52 | |
CECHHxx | 0x06 | DIA-001 | CXR714120-301GB | 0DBF | |
CECHJxx CECHKxx |
0x07 | DIA-002 | CXR714120-301GB or CXR714120-302GB |
0E69 | |
CECHLxx CECHMxx CECHPxx CECHQxx |
0x08 | VER-001 | SW-301 or SW-302 |
065D | |
CECH-20xx | 0x09 | DYN-001 | SW2-301 | 0832 | |
CECH-21xx | 0x0A | SUR-001 | SW2-301 or SW2-302 |
08A0 | |
CECH-25xx | 0x0B | JTP-001 or JSD-001 |
SW2-301 or SW2-302 or SW2-303 |
08C2 | |
CECH-30xx | 0x0C | KTE-001 | SW2-301 or SW2-302 or SW2-303 |
0918 | |
CECH-40xx | 0x0D | MSX-001 or MPX-001 |
SW3-302 | 098F |
Non retail
Model | Type | Board | Syscon part no. |
Syscon Soft ID |
Active JTAG | Notes |
---|---|---|---|---|---|---|
CEB-2040 | - | MPU-501 | CXR713F120GB-000 | Yes | Retail prototype | |
DECR1000(A/J) | 0x01 | TMU-520 | CXR713F120A | 03FB | ? | Reference tool |
DEH-H1000A(S)(-E(S)) | 0x01 | COK-001 (Prototype) | CXR713F120A | 0B67 | ? | Preproduction |
DEH-H1001-D | 0x01 | COOKIE-13 | CXR713F120A | ?0B67? | ? | Preproduction |
DEH-FH1500J-A | VERTIGO-02 | Preproduction |
Not mentioned:
0F29 - ? 0F38 - ?
Syscon Externalised Ports
Note: for more specific information per model, see the links to each subppage in the Serialnumbers @ SKU table.
Syscon UART packets
SCUART daemon (SCUARTD) packet structure
SCUARTD packets includes header of 0x3 bytes and optional payload (depending on the command). Packet IDs are not important, they are used only by clients and processed by SCUART daemon. SCUART daemon opens terminal file /dev/ttyS0 and use it to send commands and receive responses.
Offset | Size | Description |
---|---|---|
0x00 | 0x01 | Magic? |
0x01 | 0x01 | Payload size |
0x02 | 0x01 | Command |
0x03 | Payload size | Payload data |
Packets
Packet ID | Command/Action | Description | Notes |
---|---|---|---|
0x00 | version | Firmware version | Gets installed syscon's firmware version (Note: backup bank contains version 0.4.5_b4 !! ) |
0x01 | bringup | ||
0x02 | shutdown | ||
0x03 | firmud | Firmware update | Notifies about firmware update operation |
0x04 | bsn | Board Serial Number | Retrieves syscon's Board Serial Number |
0x05 | halt | Used at start of firmware update operation | |
0x06 | cp ready | ||
0x07 | cp busy | ||
0x08 | cp reset | ||
0x09 | bestat | Cell B.E. status | Retrieves Cell B.E. status |
0x0A | powersw | ||
0x0B | resetsw | ||
0x0C | bootbeep stat | ||
0x0D | bootbeep on | ||
0x0E | bootbeep off | ||
0x0F | Reset syscon | Reset | Resets syscon |
0x10 | xdrdiag info | XDR diagnostics | |
0x11 | xdrdiag start | XDR diagnostics | Starts XDR diagnostics |
0x12 | xdrdiag result | XDR diagnostics | Gets a result of XDR diagnostics |
0x13 | xiodiag | XIO diagnostics | Starts XIO diagnostics and gets a result of it |
0x14 | fandiag | Fan diagnostics | Retrieves RPMs of fans |
0x15 | errlog | Error log | Retrieves a list of codes (with timestamps) of latest errors |
0x16 | Read line | ||
0x17 | tmpforcp <zone ID> | Reference Tool's temperature | Gets the temperature of reference tool |
0x18 | Invalid CMDs | ||
0x19 | |||
0x1A | |||
0x1B | |||
0x1C | |||
0x1E | |||
0x1F | |||
0x20 | cp beepremote | ||
0x21 | cp beep2kn1n3 | ||
0x22 | cp beep2kn2n3 | ||
?? | csum | Checksum ?? | Calculates the Checksum of something (No packet ID listing on scuartd) |
Packets Logs
Packet ID | Command/Action | Logs | |
---|---|---|---|
0x00 | version | n]$ version\nv1.0.4_c2\n[mullion]$ (END) | |
0x01 | bringup | (END) | |
0x02 | shutdown | Do nothing. (PowerOff State)\n (END) | |
0x03 | firmud | Erase User Program Area Start...\n (END) | |
0x04 | bsn | ||
0x05 | halt | ||
0x06 | cp ready | ||
0x07 | cp busy | ||
0x08 | cp reset | ||
0x09 | bestat | ||
0x0A | powersw | ||
0x0B | resetsw | ||
0x0C | bootbeep stat | ||
0x0D | bootbeep on | ||
0x0E | bootbeep off | ||
0x0F | Reset syscon | ||
0x10 | xdrdiag info | ||
0x11 | xdrdiag start | ||
0x12 | xdrdiag result | ||
0x13 | xiodiag | ||
0x14 | fandiag | ||
0x15 | errlog | ||
0x16 | Read line | ||
0x17 | tmpforcp <zone ID> | ||
0x20 | cp beepremote | ||
0x21 | cp beep2kn1n3 | ||
0x22 | cp beep2kn2n3 | ||
?? | csum | Checksum ?? |
Notes
- Some commands are unavailable on earlier firmwares, for example, tmpforcp is only supported on 1.3.3+.
- Some commands are divided into several strings, the first part (if exists) describes a command group, the second part describes the actual command and other parts describes command arguments.
- Real syscon commands have an ASCII form (a bold text in the 2nd column) instead of bytes above.
- Packet with ID *0x03* notifies syscon and calls SX program (based on ZMODEM protocol) to send firmware, syscon have custom or original implementation of RX program to receive firmware. An implementation of ZMODEM protocol used by Sony: http://oss.sony.net/Products/Linux/Others/Download/DECR-1000/mips_fp_le-lrzsz-0.12.20-devtool.1.src.rpm
A start of syscon's update procedure:
- A CP development tool includes several scripts which are participated in syscon update procedure. It starts after a CP update via update_syscon.pl perl script.
- This script checks the current syscon's firmware version. If it is in mask rom then it skips an update procedure, if not it checks major/minor/release parts of both versions and if a new version is applicable then it launches scfirmup utility and pass the firmware file path as an argument.
- scfirmup is a stupid tool which prepares a connection to SCUARTD and sends an update packet with a file path inside it. There is no need to comment it, here is reimplementation: http://pastie.org/private/6h8mfeoics4mdxear7ayg
A syscon's update operation in SCUARTD consists of following steps:
- 1. Check if SX program presents in /usr/bin/sx. It should be a regular file.
- 2. Check if specified firmware file is a regular file.
- 3. Halt syscon by sending command halt to UART, then wait some time until it prints HALT: OK.
- 4. Reset syscon by sending byte 0x30 to GPIO register SC_PI0_DIPSW, byte 0x30 to GPIO register SC_RSTX, waiting 1 second and writing byte 0x31 to GPIO register SC_RSTX.
- 5. Get current syscon's firmwave version by sending command version to UART. After receiving it, look for a character after the first _ (underscore) symbol from the left side of string and if it equals to the character b, then proceed to the next step, otherwise go to the (8) step. (It is possible to patch this step to allow upgrading or downgrading at will)
- 6. Prepare syscon for an update by sending command firmud to UART, then fork the current process; the current process won't finish until a message Done from UART arrives (it is the end of update operation).
- 7. In the forked process start SX program and pass firmware file path to it. SX program reads firmware file and transfer each chunk of it to syscon.
- 8. After successful update operation reset syscon (a different way) by sending byte 0x31 to GPIO register SC_PI0_DIPSW, byte 0x30 to GPIO register SC_RSTX, waiting 1 second and writing byte 0x31 to GPIO register SC_RSTX.
Notes:
- It seems all scuartds checks firmware revision and probably syscon is updated only once (after factory).
- To be able to reflash it you need to patch SCUARTD or do a manual update without the use of SCUARTD.
- You need to patch a single byte in SCUARTD to be able to flash any firmware (for example, to downgrade your syscon).
.text:00403A94: /* scuartd from CP 1.3.3 */
lb $v1, 1($v0)
li $v0, "b" /* 62 00 02 24 -> 63 00 02 24 */
bne $v1, $v0, loc_4039F4
move $a0, $zero
- An actual firmware update process (without halting and resetting steps) takes about 1 minute.
- You cannot install a corrupted firmware with scfirmup! It seems there is a hash of sorts (possibly of the plaintext) in the header preventing scfirmup from installing something corrupt
- Updating SYSCON requires the DECR to be in standby mode! You cannot update it while it is on.
- Corrupting the header and the body will make firmup install the SYSCON update anyways! be careful not to do it!
- Should you brick SYSCON, here's a patch to "unbrick" it, do not use it unless you brick it though!
.text:004038C0:
lw $a0, 4($s4)
li $a1, 0x400000
nop
addiu $a1, (aHalt - 0x400000) # "halt"
la $t9, scuartd_send_sccmd
nop
jalr $t9 ; scuartd_send_sccmd
nop
lw $gp, 0x1E8+var_1D8($sp)
bnez $v0, loc_4039B4 /* 33 00 40 14 -> 33 00 40 10 */
li $a0, 1
Syscon UART
BGA | Name | Description |
---|---|---|
P16 | UART0_TxD | Serial Transmit |
P15 | UART0_RxD | Serial Receive |
You can attach a 3.3v TTL cable (LV-TTL) to the UART on syscon (UART0_TxD, UART0_RxD). (Convenient solder points are available on JSD/JTP-001 by the NOR test points. They are marked as '?' in marcan' noraliser / judges' NORway install picture, closest to the ground at the bottom - RX is left, TX is right) Baud rate is 57600. There is a simple plaintext protocol involved. This varies on different syscon models. Example:
<command>:<hash>
Where the hash is the sum of command bytes & 0xFF
you should terminate commands with \r\n, the syscon messages are only terminated with \n
Samples
Here are some of the commands/messages encountered:
Messages:
Power applied (standby mode) OK 00000000:3A Power on # (PowerOn State):7F Power off (Hard shutdown) # (PowerOff State):DD After Fan test: # (PowerOff State) (Fatal):36 No text, invalid hash: NG F0000002:4D
Commands:
VER:ED OK 00000000 S1E 00 00 065D:A4 ERRLOG:CB OK 00000000:3A DATE:1E NG F0000003:4E C:F1:BUZ E:4F:NG F0000004 C:D0:CID E:50:NG F0000005 C:DA:EEP E:50:NG F0000005 C:D5:FAN E:50:NG F0000005 C:F4:KSV E:50:NG F0000005 C:ED:REV E:50:NG F0000005 C:F8:SPU E:50:NG F0000005
more Syscon commands
bruteforcing commands: http://pastebin.com/CNei0xbC
VERY IMPORTANT:
- Max size of a command is 11 characters,16 if you count with C:<hash>:
- Sending a command with 11 chars results in NO OUTPUT
- Sending a command with more than 11 chars results in NG F0000002
Syscon (SPI) EEPROM
BGA | Name | Description |
---|---|---|
F16 | CSB | Chip Select (needs to be low) |
H16 | DO | Serial Data Output |
G16 | DI | Serial Data Input |
E16 | SKB | Serial Data Clock |
J15 | WCB | Write Protect |
J16 | RBB | Ready/Busy |
G11 | VDDep | + 3.3V |
C15 | VSSep | GND |
Syscon JTAG
disabled in factory after production on retailmodels
BGA | Name | Description |
---|---|---|
L8 | JRTCK | Return Test Clock |
K8 | JTCK | Test Clock |
K9 | JTDO | Test Data Out |
L9 | JTMS | Test Mode State / Test Mode Select |
K7 | JTDI | Test Data In |
L7 | JNTRST | Test Reset |
Syscon Underlaying ports
Syscon Cell SPI Bus
BGA | Name | Description |
---|---|---|
M2 | /BE_SPI_CS | Chip Select |
N2 | BE_SPI_DO | Serial Data Output |
M1 | BE_SPI_DI | Serial Data Input |
N1 | BE_SPI_CLK | Serial Data Clock |
P2 | /BE_RESET | CellBE Reset |
P1 | BE_POWGOOD | CellBE PowerGood |
T2 | /BE_INT | CellBE Interrupt |
Syscon Southbridge SPI Bus
BGA | Name | Description |
---|---|---|
B9 | /SB_SPI_CS | Chip Select |
B8 | SB_SPI_DO | Serial Data Output |
A9 | SB_SPI_DI | Serial Data Input |
A8 | SB_SPI_CLK | Serial Data Clock |
|