Search results
Jump to navigation
Jump to search
Create the page "LED" on this wiki! See also the search results found.
- ...the load/eject mechanical parts at top of the drive. SYSCON feeds this IR-LED through [[Template:Syscon_pinout_BGA_200_pads|mullion Pin M16]] (DISC_PHOT_ *IR LED (CL-200IR-X-TU)1 KB (162 words) - 22:47, 20 March 2022
- ...t led, and 10th gnd pin on a 300X model full power eject and red and green led functions, A KSW-001 Will not work on a 200X model (dsw-001 slot) not teste1 KB (182 words) - 03:40, 20 July 2017
- ...t led, and 10th gnd pin on a 300X model full power eject and red and green led, A KSW-001 Will not work on a 200X model (dsw-001 slot).2 KB (264 words) - 03:56, 20 July 2017
- ...w Light of Death" sequence was changed with this revision, where the power LED no longer turns yellow, although the rest of the sequence is the same. ...button three times, then power button twice. If done correctly, the power LED should now blink yellow once (to indicate the mode has been activated) then2 KB (363 words) - 13:26, 11 March 2024
- *BOARD = USER (need to manually attribute LED pins in Board/LEDs.h) ...ould light up. After about 5 seconds, the second LED will light up (or the LED will just go off, if you only have one). This means the exploit worked! You4 KB (663 words) - 23:33, 14 July 2017
- ...to the 5 volts standby line present in the switch board at all times). All LED's have its own resistor with a different value to control the current (thus *Contour LED's13 KB (2,279 words) - 03:57, 20 July 2017
- *Eject LED should be connected to BD controller [[CXD5063AGG-1]]874 bytes (121 words) - 01:18, 16 October 2020
- *Pin 36 goes to a transistor and then to EJECT blue led on [[Switch boards|switch board]]. See: http://www.psdevwiki.com/ps3/File:S873 bytes (129 words) - 10:50, 11 February 2023
- # RSSI‚ª‹KŠi“à(-OK-)‚ÌꇂÉs‚¤LED§Œä # LED ID16 KB (1,900 words) - 04:43, 1 July 2023
- **'''Eject led''', this is the only led not controlled by syscon, the line goes to the bluray controller, so is the **All LED's have its own resistor with a different value to control the current (thus13 KB (1,858 words) - 19:27, 5 December 2021
- Fourth PS3 slim model. Optical drive LED, WiFi activity light have been removed. Sony symbol above the optical drive1 KB (160 words) - 00:31, 1 February 2024
- == LED Diag Mode == Cannot seem to get led diag to work on CECHA fats, don't know what FW version (because requiring f11 KB (1,789 words) - 17:38, 31 December 2023
- | 6 || LED[0] || O || LED/Interrupt outputs | 8 || LED[1] || O || LED/Interrupt outputs9 KB (1,356 words) - 15:10, 5 February 2014
- ...1~4 || 60,48,44,34 || 45,35,32,23 || 1,3,4: O<br />2: B<br />(pd) || Green LED indicator for DSPORT1~4<br />*GREEN[1~2] are also used to access the extern | AMBER1~4 || 61,49,45,35 || 46,36,33,24 || O<br />(pd) || Amber LED indicator for DSPORT1~4<br />*Amber [1~2] are also used to access the exter4 KB (547 words) - 07:14, 17 April 2023
- The LED Diagnostics Mode that was accessible from 21xx to 30xx slims was either cha2 KB (292 words) - 12:56, 19 May 2024
- ...Death" sequence was changed yet again with this revision, where the power LED simply turns off after the initial green, and the three sequential beeps ar2 KB (287 words) - 16:26, 31 December 2023
- | 1 || RST || rowspan="36" | Power / Led / Xtal etc || - Connectortype: RJ45 modular jack with LED | PartNo.: 1-820-763-126 KB (895 words) - 15:17, 5 February 2014
- | SLL || LED related3 KB (372 words) - 02:49, 7 March 2020
- ...on and the Eclips3 dongle will light up the red LED followed by the green LED. Turn off your PS3 via menu.<br /> ...-inserted-in-FAT-PS3-green-led-lit.png|Eclipse inserted in FAT PS3 - green led lit]]<br />13 KB (2,063 words) - 22:49, 29 March 2024
- | 10 || GPIO15 || GPIO15 - CompactFlash Access LED | 66 || GPIO13 || GPIO13 - Memory Stick Access LED6 KB (796 words) - 05:09, 9 June 2015